« previous next »
Pages: [1]   Go Down

Author Topic: Goodyear D2585 Question  (Read 4952 times)

Offline jspell

  • Full Member
  • ***
  • Posts: 132
    • View Profile
  • Your Best Time: 7.48 / 178
  • Your Track: Maple Grove Raceway
  • Your Vehicle: 2014 Ken Keir Dragster
Goodyear D2585 Question
« on: May 15, 2014, 08:20:46 AM »
Does anyone have the "bubble" dimension using a 12" rim on a D2585?  I'm trying to determine correct back-spacing for new wheels. Looking for dimension from edge of rim to outside of slick...any info is appreciated. thanks
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Goodyear D2585 Question
« Reply #1 on: May 15, 2014, 03:12:22 PM »
If you can wait a couple of days I am mounting a set of them up. If it helps my rims are 3 1/2 backspace and my axle flange is 7 1/2 away from the frame . With that set up I had plenty of room with that tire .
Logged

Offline jspell

  • Full Member
  • ***
  • Posts: 132
    • View Profile
  • Your Best Time: 7.48 / 178
  • Your Track: Maple Grove Raceway
  • Your Vehicle: 2014 Ken Keir Dragster
Re: Goodyear D2585 Question
« Reply #2 on: May 16, 2014, 04:32:40 AM »
Thanks
Logged

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: Goodyear D2585 Question
« Reply #3 on: May 16, 2014, 11:12:33 PM »
On our 12" wide wheels with 6 lbs of pressure my D2585's have 1 1/2" from the rim edge to the sidewall.
The less tire pressure the more the sidewall "bubbles", less tire growth. With only a couple pounds of pressure my tires where at 2 1/4"
We make about 900 hp with our Heritage Jr Fueler, and need the 12" rim because with the 11" rim it would get loose at about half track. We ran 10" rim for about 8 years, which gave us more tire growth, ie less RPM at the finish.  Are you sure you need a 12" rim ?
Logged
Jon C. Hansen

Hayden Wheels

Offline jspell

  • Full Member
  • ***
  • Posts: 132
    • View Profile
  • Your Best Time: 7.48 / 178
  • Your Track: Maple Grove Raceway
  • Your Vehicle: 2014 Ken Keir Dragster
Re: Goodyear D2585 Question
« Reply #4 on: May 18, 2014, 05:16:51 PM »
Jon, not sure I need a 12", was thinking it might be a btter way to go in case of marginal track condition.  My engine is carburated and makes 805 HP at 7400, with 1.76 glide, and 4.22 R&P.  Should I go with 10"?
Logged
Pages: [1]   Go Up
« previous next »