« previous next »
Pages: [1]   Go Down

Author Topic: fresh engine test  (Read 3656 times)

Offline spookie

  • Jr. Member
  • **
  • Posts: 61
    • View Profile
  • Your Best Time: 8.92 1/4 5.59 1/8
  • Your Track: Quarter Aces drag-o-way
  • Your Vehicle: F.E.D.
fresh engine test
« on: December 25, 2019, 05:42:02 AM »
Put together sbc with new solid lifter cam.Would it be safe to test run for a short time without water? How long would be safe? Have VR-1 race oil.
Logged

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: fresh engine test
« Reply #1 on: December 25, 2019, 06:07:26 AM »
I've done that. I only run it for a minute usually. But bear in mind some drag cars run with NO  water - only oil cooling from crankcase splash. so I suspect you could run it for longer especially since it will not be under load and flowing any significant amount of fuel through it.

If you have a vacuum pump I think I would disconnect that to keep the max amount of oil splashing and spewing out the bearings.
« Last Edit: December 25, 2019, 06:11:04 AM by THE FRENCHTOWN FLYER »
Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: fresh engine test
« Reply #2 on: December 27, 2019, 06:35:47 AM »
If it is a flat tappet solid the answer is No
Initial start up and cam/lifter break in is Critical on any build
You will just increase the chances of grinding a lobe off
You need instant start up, full water flow, timing set instantly ( well advanced never ever too low--makes giant heat if too low) and let it run at about 2000-2300 RPM until it comes up to temp-let it cool--repeat about half dozen times to give the cam and lifters every chance possible--you should do all this with inner springs out to reduce pressure
If you do this and all of your lifter bores were perfect ( hopefully sized with a ball broach) your cam has a fighting chance
Good luck--do it right
I would break it in on test stand--
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline jeff/21

  • Full Member
  • ***
  • Posts: 186
    • View Profile
  • Your Best Time: 8.24
  • Your Track: any with-in a 6hr radius
  • Your Vehicle: fed
Re: fresh engine test
« Reply #3 on: December 27, 2019, 11:28:03 AM »
dusterdave173 is right and don't let the motor idle down keep on a fast idle
Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: fresh engine test
« Reply #4 on: December 28, 2019, 01:27:53 PM »
We started using the lifter bore broach from Goodson machine supply--it is wonderful--most engine getthe lifer bores hurt on tear down--naturally the old lifter is mushroomed a small amount from wear--most folks yank them out the top--Pro builders always remove cam then push lifter out the bottom that way you don't scratch the lifter bore up
The ball broach is hammered through and then slide hammered back out this straightens the lifter bore and smooths it up
This process is a must when block has been shot blasted too ( always use WD40 or some similar on each bore as you do this)
Cheap tool that works miracles and as a bonus helps you find if a lifter bore is worn too much ( big trouble too )
We all know about oil with correct additives, spring pressures being right etc but many still ignore the lifter bores and then wind up blaming cam and lifters for failure
This process helped my shop avoid cam / lifter issues and cut failures to almost zero
The balls are available for all popular lifter diameters but also come as a kit with popular chevy ford and mopar
They are hard as Supermans knee cap and should last forever
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: fresh engine test
« Reply #5 on: January 02, 2020, 06:06:08 AM »
All good reason to run a roller cam.Cheaper in long run.JMO
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot
Pages: [1]   Go Up
« previous next »