« previous next »
Pages: [1]   Go Down

Author Topic: Burndown breather puke tank  (Read 5492 times)

Offline RacinJacin

  • Newbie
  • *
  • Posts: 40
    • View Profile
  • Your Best Time: 9.30's
  • Your Track: Thompson
  • Your Vehicle: FED
Burndown breather puke tank
« on: July 01, 2019, 07:21:09 PM »
Early hemi, please share pics of your puke tank. I need to fab something  - it'd be very helpful to see whats been done.  Thanks!!!!!!!
Logged

dreracecar

  • Guest
Re: Burndown breather puke tank
« Reply #1 on: July 02, 2019, 09:47:56 AM »
Funny Car , but the same concept
Logged

Offline MikenMpls

  • Jr. Member
  • **
  • Posts: 80
    • View Profile
  • Your Engine: 408 dart little m block and Iron Eagle heads
  • Your Track: Cameron, MO
  • Your Vehicle: 205" FED
Re: Burndown breather puke tank
« Reply #2 on: July 02, 2019, 03:45:35 PM »
My next breather tank will include a port for the transmission vent. why have a separate tank for it when one will do.
Logged

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Burndown breather puke tank
« Reply #3 on: July 03, 2019, 05:23:50 AM »
That's pretty. But I wonder what keeps condensation from building up in the frame and eventually filling the tubes?
Logged

dreracecar

  • Guest
Re: Burndown breather puke tank
« Reply #4 on: July 03, 2019, 08:20:41 AM »
Threaded drain plugs are fitted to the tubing at the front end.
Logged

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Burndown breather puke tank
« Reply #5 on: July 04, 2019, 08:08:28 PM »
I see. After how many runs - gas or alky - do you generally have to pop the plugs and drain? Also, do you run electrical wiring through the lower tube(s) then?
Logged

dreracecar

  • Guest
Re: Burndown breather puke tank
« Reply #6 on: July 05, 2019, 09:04:50 AM »
Just during normal car maintanence or after a blow-up. The right lower frame rail usually contains the front brake line and the fire bottle cable as those have to be shielded where they pass the clutch can/motor plate.  I some cases,by the rules, all wiring must be exposed , even with that, trouble shooting a wiring/air line issue is a lot easier without running them inside the frame. Most builds run them thru tunnels in the motorplate uprites
Logged

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Burndown breather puke tank
« Reply #7 on: July 05, 2019, 11:59:00 AM »
Thanks for the insight. It sounds like there is either not a lot of condensation taking place or the flow rate is high enough to purge all that glop from the frame.
My [unblown] altered has the wires inside the rail tubing (except trans brake), that's why I asked.
Logged

dreracecar

  • Guest
Re: Burndown breather puke tank
« Reply #8 on: July 05, 2019, 04:32:19 PM »
You have to remember to pull everything out the tubing before you can weld repair.  I told a customer to do that except he forgot one line, "Hey, do you smell something burning"?
 Also you have to clean the vent tube real good before welding or it becomes a mess and the drain helps clear the solvent.
Logged

Offline RacinJacin

  • Newbie
  • *
  • Posts: 40
    • View Profile
  • Your Best Time: 9.30's
  • Your Track: Thompson
  • Your Vehicle: FED
Re: Burndown breather puke tank
« Reply #9 on: July 24, 2019, 09:30:23 PM »
For you curious guys - here's what I ended up fabbing. Made pretty much everything even the breather because I struck out at the local swapmeets and I'm not a patient person sometimes. "AMF" is a tribute to my buddy Stan that helped me run the car from the beginnng until he passed. "Adios...."
If you look close at the tank you will see the end caps are domed.  My press and a PVC CAP was all that was neeed to make those.


Jacin
Logged
Pages: [1]   Go Up
« previous next »