« previous next »
Pages: [1]   Go Down

Author Topic: Aluminum sbc  (Read 5914 times)

Offline Guido

  • Newbie
  • *
  • Posts: 32
    • View Profile
  • Your Best Time: 7.52 185 mph
  • Your Engine: Supercharged sbc
  • Your Track: Kearney raceway park
  • Your Vehicle: 170" FED
  • General Location: Mid westMHRUWX
Aluminum sbc
« on: March 18, 2019, 11:41:18 AM »
Any thoughts on running an aluminum block sbc with a dry sump on alcahol without water?
Logged

dreracecar

  • Guest
Re: Aluminum sbc
« Reply #1 on: March 18, 2019, 11:59:38 AM »
Run/Ran aluminum SBC (Donovan) for 24 years, dry block ,wet sump, Water is only critical in the heads to keep from burning up between the exhaust valves. Unless you get/got a smokin deal on a Sprint Car dry sump block, it's weight and lots of expense without any real gain
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Aluminum sbc
« Reply #2 on: March 18, 2019, 01:44:18 PM »
I run a Brodix block and AJPE heads I run dry.  If I had a conventional headed SBC I would run water in the heads.
Logged

Offline glofria

  • Full Member
  • ***
  • Posts: 138
    • View Profile
  • Your Best Time: 7.323 @ 185.05
  • Your Engine: A blown 388 c.i. Small Block Chevy
  • Your Track: Auto Club Famoso Raceway
  • Your Vehicle: An original 1957 Chevy Bel-Air
  • General Location: Southern California
Re: Aluminum sbc
« Reply #3 on: March 20, 2019, 01:57:25 PM »
We run a Dart block w/ Brodex symmetrical style heads and a VHS dry sump system; blown application.

In the past we have used standard style heads while circulating Evans Coolant through the heads only by way of a VW Scirraco electric water pump.

https://www.evanscoolant.com/products/high-performance-coolant/
Logged

Offline glofria

  • Full Member
  • ***
  • Posts: 138
    • View Profile
  • Your Best Time: 7.323 @ 185.05
  • Your Engine: A blown 388 c.i. Small Block Chevy
  • Your Track: Auto Club Famoso Raceway
  • Your Vehicle: An original 1957 Chevy Bel-Air
  • General Location: Southern California
Re: Aluminum sbc
« Reply #4 on: March 20, 2019, 02:00:59 PM »
One other thing worth noting. with a narrow dragster chassis we mounted the pump under/ off to the side of the oil pan. Must use a shallow pan.

If you want to see a photo, I'll have to dig around for one.
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Aluminum sbc
« Reply #5 on: March 20, 2019, 05:09:44 PM »
Quote from: glofria on March 20, 2019, 02:00:59 PM
One other thing worth noting. with a narrow dragster chassis we mounted the pump under/ off to the side of the oil pan. Must use a shallow pan.

If you want to see a photo, I'll have to dig around for one.

I ran a Kuhl River Rat pump
Logged

Offline Guido

  • Newbie
  • *
  • Posts: 32
    • View Profile
  • Your Best Time: 7.52 185 mph
  • Your Engine: Supercharged sbc
  • Your Track: Kearney raceway park
  • Your Vehicle: 170" FED
  • General Location: Mid westMHRUWX
Re: Aluminum sbc
« Reply #6 on: March 22, 2019, 07:48:03 AM »
 :-*photos would be great, trying to figure out pump and tank locations
Logged

dreracecar

  • Guest
Re: Aluminum sbc
« Reply #7 on: March 22, 2019, 08:41:20 AM »
If you decide to go with a belt driven oil pump, install the fuel pump to it also, that way when the pump fails or belt breaks the engine stops running and don't tear it up running it without oil pressure
Logged

Offline glofria

  • Full Member
  • ***
  • Posts: 138
    • View Profile
  • Your Best Time: 7.323 @ 185.05
  • Your Engine: A blown 388 c.i. Small Block Chevy
  • Your Track: Auto Club Famoso Raceway
  • Your Vehicle: An original 1957 Chevy Bel-Air
  • General Location: Southern California
Re: Aluminum sbc
« Reply #8 on: March 22, 2019, 09:28:33 AM »
If the belt breaks it's more than likely because the pump seized and it'll be too late by then anyways. Have not seen both pumps driven off the same belt before. In line with each other, but not side by side.
Logged

dreracecar

  • Guest
Re: Aluminum sbc
« Reply #9 on: March 22, 2019, 09:51:52 AM »
My statement was in regards to install in-line. Back in my Sprint/Midget days, belt drives were an issue. I still fail to see any measurable benefit to a D-S system in what we do
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Aluminum sbc
« Reply #10 on: March 23, 2019, 05:52:24 AM »
This one mounts the fuel pump on the back of the oil pump !
Logged

Offline OldSchoolHP

  • Newbie
  • *
  • Posts: 13
    • View Profile
  • Your Best Time: 8.92/158 - 1320'
  • Your Engine: 434 SBC
  • Your Track: AK Raceway Park
  • Your Vehicle: 125 Altered
  • General Location: Alaska
Re: Aluminum sbc
« Reply #11 on: October 27, 2020, 12:26:36 AM »
I think the aluminum block takes the center cylinder heat better than any Iron block. The Iron gets Hot and stays hot. Aluminum dissipates that heat. Make sure you feed the center cylinders a bit more fuel to keep them happy, youll get several more runs out of the head gaskets compared to Iron. Just my .02c.
Logged
Pages: [1]   Go Up
« previous next »