Author Topic: Mr Miller a question >>>  (Read 5321 times)

Offline LZ

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Engine: In progress
  • Your Track: Empire Dragway
  • Your Vehicle: 2010 225" S&W
Mr Miller a question >>>
« on: June 09, 2016, 03:40:01 AM »
>>> for you and its not spark or fuel related ;)

At this thread your name was mentioned and wondered if you could comment about the gear heat treatment talk.
if ya get a chance down about 4 or 5 posts.
http://www.frontenginedragsters.org/forum/index.php/topic,2169.0.html

Thank you
Luke
"I am not a number.... I am a free man."

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Mr Miller a question >>>
« Reply #1 on: June 09, 2016, 07:35:53 AM »

 Sure!

 I run a 2.91 rear gear in my Ford 9". It was impossible to find a Pro gear in that ratio that would fit. I called Richmond and talked to an engineer there. He pointed me to a 2.91 street gear and told me how to "draw it back" or anneal it to help it resist cracking and breaking.

 Put the ring and pinion (no bearings on it of course) on a cookie sheet. Put it in the kitchen oven and turn it on to 500F. Let it bake 2-3 hours...it MUST reach 500F in the middle for a while. When the time has elapsed, turn the oven off and leave it to cool down slowly over night. DON'T OPEN THE DOOR. Just turn it off, walk away and come back tomorrow.

 They will have changed color...don't worry, normal. That means it worked!

 I'm still running those gears and they look great.

 Spud

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

dreracecar

  • Guest
Re: Mr Miller a question >>>
« Reply #2 on: June 09, 2016, 08:06:44 AM »
I tried doing that once for a customer, Wife would not talk to me for a week

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Mr Miller a question >>>
« Reply #3 on: June 09, 2016, 09:00:45 AM »

 Yes, even if the gears are new and super clean, the next batch of cookies might taste funny :)

 I always wanted an oven/stove top, dishwasher and washer/dryer of my own in the shop. Washing towels/rags/parachutes, clean parts, bake coatings, etc. without screwing up the good stuff in the house. Unfortunately, no room for all that...shop space is too valuable!

 Spud

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline Paul New

  • Hero Member
  • *****
  • Posts: 744
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Mr Miller a question >>>
« Reply #4 on: June 09, 2016, 09:05:34 AM »
we have a $10 garage sale oven in our shop works great!

Offline LZ

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Engine: In progress
  • Your Track: Empire Dragway
  • Your Vehicle: 2010 225" S&W
Re: Mr Miller a question >>>
« Reply #5 on: June 15, 2016, 07:43:45 PM »
Spud - Bruce
Did you by any chance do a Rockwell on them ??
Thanks
Luke
"I am not a number.... I am a free man."