Author Topic: Methanol / Nitro in epoxied heads?  (Read 6539 times)

Offline Big Rhino

  • Newbie
  • *
  • Posts: 15
    • View Profile
  • Your Best Time: no runs yet
  • Your Track: Gulfport
  • Your Vehicle: 225" FED
Methanol / Nitro in epoxied heads?
« on: March 23, 2014, 03:51:53 PM »
I am building a BBC and the heads are older EPD Racing and are extensively ported with epoxy.  I plan to run my stack injection on methanol and occasionally up to 30% Nitro.  Is this going to be a problem with the epoxy?

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Methanol / Nitro in epoxied heads?
« Reply #1 on: March 25, 2014, 11:32:22 AM »
I can't tell you about nitro but I run my car and alcohol . I use epoxy on my small block heads and have had no issues . The best epoxy to use is called splash zone . It is a marine epoxy and it works very well . I have also heard that some engine builders will cover the epoxy with a clear urathane paint . I hope this helps . Bill

Offline Big Rhino

  • Newbie
  • *
  • Posts: 15
    • View Profile
  • Your Best Time: no runs yet
  • Your Track: Gulfport
  • Your Vehicle: 225" FED
Re: Methanol / Nitro in epoxied heads?
« Reply #2 on: March 27, 2014, 03:07:31 AM »
Thanks for the info.  I heard rumors of epoxied heads running methanol and the epoxy degrading/melting/peeling out..etc.  I was just wondering if there is anything to worry about.  Don't know what type of epoxy was used on mine, I bought the heads used.

Offline andrewb

  • Jr. Member
  • **
  • Posts: 57
    • View Profile
  • Your Track: Woodburn
  • Your Vehicle: Flathead
Re: Methanol / Nitro in epoxied heads?
« Reply #3 on: March 28, 2014, 09:04:30 AM »
We run 90% nitro with epoxy filled heads/block and have no problems. Lately, at the rate my wife goes through engines, we haven't had a block last more than two years, although we have another engine that's been running for over 10 years without any issues.

Andrew

Offline Big Rhino

  • Newbie
  • *
  • Posts: 15
    • View Profile
  • Your Best Time: no runs yet
  • Your Track: Gulfport
  • Your Vehicle: 225" FED
Re: Methanol / Nitro in epoxied heads?
« Reply #4 on: March 28, 2014, 10:59:56 PM »
Excellent, I feel much better now!   ;)

Offline slingshot383

  • Full Member
  • ***
  • Posts: 143
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: Methanol / Nitro in epoxied heads?
« Reply #5 on: April 15, 2014, 09:17:12 AM »
After 5 seasons, the epoxy is pretty well toast, and will need to be redone.  Not so much the fuel as the heat/ cold cycles causing the issue.
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club

Offline Big Rhino

  • Newbie
  • *
  • Posts: 15
    • View Profile
  • Your Best Time: no runs yet
  • Your Track: Gulfport
  • Your Vehicle: 225" FED
Re: Methanol / Nitro in epoxied heads?
« Reply #6 on: April 18, 2014, 11:30:43 AM »
Yep, now that I think about it, it actually makes sense.  Rats, I hope these heads make it a season or two.  I will have to inspect them more frequently I guess.  I believe I will just stay with the methanol, no nitro.
Thanks guys!