« previous next »
Pages: [1]   Go Down

Author Topic: Zoomie Header Size  (Read 9601 times)

Offline jspell

  • Full Member
  • ***
  • Posts: 132
    • View Profile
  • Your Best Time: 7.48 / 178
  • Your Track: Maple Grove Raceway
  • Your Vehicle: 2014 Ken Keir Dragster
Zoomie Header Size
« on: April 08, 2014, 01:04:48 PM »
What size headers are you guys using on your SBC race engines?  1-7/8, 2". 2-1/8?
Logged

dreracecar

  • Guest
Re: Zoomie Header Size
« Reply #1 on: April 08, 2014, 01:08:46 PM »
I run 2 1/8" just for the look. My heads have the 7 bolt pattern in them . stock can only go to 1 3/4" before you have to run adapters.
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Zoomie Header Size
« Reply #2 on: April 08, 2014, 01:23:01 PM »
I just built a set for mine and they are 2 inch . When I ran the collector headers they were stepped 1 7/8 to 2 inch . The zoomies are a little slower
Logged

Offline PSweeney

  • Full Member
  • ***
  • Posts: 231
    • View Profile
  • Your Track: Santa Pod
  • Your Vehicle: 138in SBC slingshot
Re: Zoomie Header Size
« Reply #3 on: April 15, 2014, 07:09:26 AM »
we have Stahl adapters and 2in pipes
Logged

Offline MaggiFinn

  • Jr. Member
  • **
  • Posts: 54
    • View Profile
  • Your Engine: SBC 355-406
  • Your Track: Kvartmiluklubburinn
  • Your Vehicle: FED
Zoomie Header Size
« Reply #4 on: April 16, 2014, 03:15:57 AM »
Mine are stepped from 1.3/4 to 2"  and have the shape of funny car zoomies.
Stepped are about 2" in length and the pipes are 28-30" long
You can see where the blue heat mark ends, no idea if that is good or bad. It did not noticably change going from N/A to nitrous.
« Last Edit: April 16, 2014, 03:20:31 AM by MaggiFinn »
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Zoomie Header Size
« Reply #5 on: April 16, 2014, 12:32:05 PM »
How did your car like the nitrous and how much were you spraying ?
Logged

Offline MaggiFinn

  • Jr. Member
  • **
  • Posts: 54
    • View Profile
  • Your Engine: SBC 355-406
  • Your Track: Kvartmiluklubburinn
  • Your Vehicle: FED
Zoomie Header Size
« Reply #6 on: April 16, 2014, 04:10:03 PM »
Last time out It took an 80 jet on the first kit and 72 on second. Both big shot plates. Second kit came in on the shift.
« Last Edit: April 16, 2014, 04:14:55 PM by MaggiFinn »
Logged
Pages: [1]   Go Up
« previous next »