Author Topic: Coupler Cover ?  (Read 18426 times)

Offline ss4

  • Jr. Member
  • **
  • Posts: 98
    • View Profile
  • Your Best Time: 5.42 @ 128 - 1/8th
  • Your Track: Northern Michigan Dragway
  • Your Vehicle: Worm Inc. 180 inch Front Engine Dragster
Re: Coupler Cover ?
« Reply #15 on: March 11, 2014, 01:29:22 PM »
general rules  2:4

  copy & pasted off NHRA Heritage rules  2013-14

thanks I wasn't questioning, I just wasn't finding it for some reason.
if you need to Hate target Laziness

dreracecar

  • Guest
Re: Coupler Cover ?
« Reply #16 on: March 11, 2014, 01:35:32 PM »
Not a problem

Offline ss4

  • Jr. Member
  • **
  • Posts: 98
    • View Profile
  • Your Best Time: 5.42 @ 128 - 1/8th
  • Your Track: Northern Michigan Dragway
  • Your Vehicle: Worm Inc. 180 inch Front Engine Dragster
Re: Coupler Cover ?
« Reply #17 on: March 12, 2014, 05:48:26 AM »
hey so I made a quick check on mine for thickness and I didn't screw up.  it is .155 not .100.  Yeah something I don't have to remake.
if you need to Hate target Laziness

Offline PSweeney

  • Full Member
  • ***
  • Posts: 231
    • View Profile
  • Your Track: Santa Pod
  • Your Vehicle: 138in SBC slingshot
Re: Coupler Cover ?
« Reply #18 on: March 12, 2014, 07:31:24 AM »
Some tech people could consider them "Temporary" fasteners. and you are still too thin on the material thickness  .125"

thanks for posting, looks like a neat set up.

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Coupler Cover ?
« Reply #19 on: March 12, 2014, 02:02:37 PM »
Question on this subject since its one thing I still have not made up. Since mines soild shaft with couplers and I will need quick access will two piece tube in slip fashion work? One fastened to the rear ,other sliding over it to trans with some sort of locking divice in middle on top,still working on that part. Mines is also about 12" from trans to rear coupler
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

dreracecar

  • Guest
Re: Coupler Cover ?
« Reply #20 on: March 12, 2014, 04:17:02 PM »
You can telescope the 2 pieces or you can split the tube and have marmon band clamps on each end as long as the split tube goes around somthing on each end and one clamp in the middle. just make sure you cut any excess thread past the nut to keep from getting hung up.

Offline PSweeney

  • Full Member
  • ***
  • Posts: 231
    • View Profile
  • Your Track: Santa Pod
  • Your Vehicle: 138in SBC slingshot
Re: Coupler Cover ?
« Reply #21 on: March 13, 2014, 08:08:42 AM »
Question on this subject since its one thing I still have not made up. Since mines soild shaft with couplers and I will need quick access will two piece tube in slip fashion work? One fastened to the rear ,other sliding over it to trans with some sort of locking divice in middle on top,still working on that part. Mines is also about 12" from trans to rear coupler

on the first version of my set up, I split a piece of 4" tube and welded tabs to bolt the two halves together, the principle being I can push the yoke back into the box and lift the motor/ trans out vertically once the steering gear is swung out the way.