Author Topic: 6-71 GMC Blower and Hilborn Injection SBC  (Read 8873 times)

Offline patina

  • Newbie
  • *
  • Posts: 21
  • Thanks to Dave Daly and Willie "The Welder" Feyh
    • View Profile
  • Your Best Time: 10.63 1/4 mile
  • Your Engine: Chev. gas, 350"
  • Your Track: Lebanon Valley Dragway NY
  • Your Vehicle: 1952 MG ran BM/SP at Indy Nats 64
6-71 GMC Blower and Hilborn Injection SBC
« on: February 24, 2014, 01:31:09 PM »
A 6-71 GMC blower with a like new (I don't think it was ever used) 2 port Hilborn fuel injection and original Hilborn scoop again like new. Comes with Hilborn pump # PG 150-A  sn 1-3814 and cam drive extension w/rod, 2" wide belts, 40T blower pulley, 34 T crank pulley, degreed Isky crank hub w/v-belt groove and water pump pulley (for street use w/ stock WP), Weiand front and rear covers,
Weiand CV6-71 intake manifold, 2 different idler pulley set-ups various hardware. Cert. of Authenticity from Hilborn injector was purchased new from S&S Speed Shop  in Richmond Hill NY on 6/5/67 It was a friend of mine and he was putting the blower on his Buick powered 55 T-Bird but it never happened, I bought all his stuff in 1972 and it has been sitting on the shelf all these years now health issues force me to get rid of a lot of my parts. The blower had been gone through when he had it, the guy was a machinist and very particular it is dirty and dusty now but I have not turned the blower because I would clean it first (It does turn). This is definitely a period correct piece and would go beautifully on that FED or Gasser or maybe even an early Funny car. Price is $3500.00 for everything.

Pat

Offline patina

  • Newbie
  • *
  • Posts: 21
  • Thanks to Dave Daly and Willie "The Welder" Feyh
    • View Profile
  • Your Best Time: 10.63 1/4 mile
  • Your Engine: Chev. gas, 350"
  • Your Track: Lebanon Valley Dragway NY
  • Your Vehicle: 1952 MG ran BM/SP at Indy Nats 64
Re: 6-71 GMC Blower and Hilborn Injection SBC
« Reply #1 on: April 19, 2014, 09:17:26 AM »
Just back from "Big Al's" he did a complete tune-up and cleaning on blower and it comes with a one year warranty on blower. Cost me $500.00 for this service it's now ready to run, price is still $3500.00.

Call at 845-758-8756 or E-mail at linguinebros@yahoo.com

Pat

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 570
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: 6-71 GMC Blower and Hilborn Injection SBC
« Reply #2 on: April 19, 2014, 10:10:35 AM »
Pat,

This is a nice vintage setup and it would sure look great on my 60's FED. The price doesn't seem too bad. But as usual, that's not an ideal time for me for big check purchase.

I wish you sell it quickly, so I don't keep drooping on this ad.

Offline buickfed

  • Full Member
  • ***
  • Posts: 191
    • View Profile
Re: 6-71 GMC Blower and Hilborn Injection SBC
« Reply #3 on: April 19, 2014, 11:34:37 AM »
if that's a nailhead intake, you will need to measure across for bolt width to figure out which size engine it fits. there are 3 different widths.

Offline patina

  • Newbie
  • *
  • Posts: 21
  • Thanks to Dave Daly and Willie "The Welder" Feyh
    • View Profile
  • Your Best Time: 10.63 1/4 mile
  • Your Engine: Chev. gas, 350"
  • Your Track: Lebanon Valley Dragway NY
  • Your Vehicle: 1952 MG ran BM/SP at Indy Nats 64
Re: 6-71 GMC Blower and Hilborn Injection SBC
« Reply #4 on: April 19, 2014, 12:19:06 PM »
The manifold is for a "Small Block Chevy" It is a Weiand CV6-71. Sorry for any confusion.

Pat

Offline gasserx

  • Full Member
  • ***
  • Posts: 192
    • View Profile
  • Your Best Time: 1/4 - 9.08
  • Your Track: Gardermoen Raceway
  • Your Vehicle: 180" FED
Re: 6-71 GMC Blower and Hilborn Injection SBC
« Reply #5 on: June 26, 2014, 01:37:10 AM »
Interested in splitting the kit and sell the Hilborn-stuff separate?

Offline Quain Stott

  • Newbie
  • *
  • Posts: 9
    • View Profile
  • Your Best Time: 3.67 207 MPH 1/8 mile Pro Mod car
  • Your Track: Greer SC dragway
  • Your Vehicle: 41 willys period correct gasser
Re: 6-71 GMC Blower and Hilborn Injection SBC
« Reply #6 on: August 17, 2014, 01:14:03 PM »
Do you still have the blower stuff for sale thank's

Offline patina

  • Newbie
  • *
  • Posts: 21
  • Thanks to Dave Daly and Willie "The Welder" Feyh
    • View Profile
  • Your Best Time: 10.63 1/4 mile
  • Your Engine: Chev. gas, 350"
  • Your Track: Lebanon Valley Dragway NY
  • Your Vehicle: 1952 MG ran BM/SP at Indy Nats 64
Re: 6-71 GMC Blower and Hilborn Injection SBC
« Reply #7 on: August 17, 2014, 01:41:30 PM »
Sold in it's entirety

Pat

Online JoydayVox

  • Full Member
  • ***
  • Posts: 182
    • View Profile
    • how to buy priligy as a child
  • Your Best Time: Urenulo
  • Your Engine: Ekubyboxe
  • Your Track: Ysehekol
  • Your Vehicle: Ijesu
  • General Location: Eweciq
Re: 6-71 GMC Blower and Hilborn Injection SBC
« Reply #8 on: November 07, 2024, 07:41:20 AM »
Insurance and Medicare prescription plans typically cover Estrace and Premarin <a href=https://fastpriligy.top/>viagra priligy</a> Increased DNA binding and transcriptional activity of AP 1 complexes expressed in TAM resistant MCF7 HER2, BT474 relative to TAM sensitive MCF7 breast cancer cells