« previous next »
Pages: [1]   Go Down

Author Topic: My first front engine dragster--need history  (Read 11469 times)

Offline novacain

  • Newbie
  • *
  • Posts: 19
    • View Profile
  • Your Best Time: 10.80 @ 123 in the 1/4
  • Your Track: Gateway motorsports park----St. Louis, Mo
  • Your Vehicle: 166" FED
My first front engine dragster--need history
« on: November 22, 2013, 09:06:29 PM »
Got my first front engine dragster and am trying to find some history on it. Car is 168" wb . 8 3/4 Chrysler rear, center steer with the bell crank on the outside of the left tube, torsion bar behind the axle. Car is mild steel, was told the car was built in the early 70's and I've traced it back to Michigan. Trying to figure out who built it.  Any ideas would be helpful. Thanks in advance.
Logged

Offline Sidewinder

  • Jr. Member
  • **
  • Posts: 90
    • View Profile
  • Your Track: Kjula Raceway
Re: My first front engine dragster--need history
« Reply #1 on: November 23, 2013, 04:26:39 AM »
Congrats with your FED:) Have you talked to your local FED supplier? Brian Fox, KING chassis?

K
Logged

dreracecar

  • Guest
Re: My first front engine dragster--need history
« Reply #2 on: November 23, 2013, 08:45:12 AM »
First you need more pictures concentrating on different areas, overall picture of a car painted black  tells nothing.

Any major chassie builder of that time would never build a frame with mild steel. What is the width inside the shoulder hoop??
Logged

Offline novacain

  • Newbie
  • *
  • Posts: 19
    • View Profile
  • Your Best Time: 10.80 @ 123 in the 1/4
  • Your Track: Gateway motorsports park----St. Louis, Mo
  • Your Vehicle: 166" FED
Re: My first front engine dragster--need history
« Reply #3 on: November 23, 2013, 02:41:58 PM »
Haven't talked to anyone local yet, figured i'd try here first. From what I've read so far, I think I've got a homebuilt copy of someone else's design. The guy I got the car from said he bought it from a guy in Michigan, doesn't remember his name, too many years ago. Car was supposedly built in the early 70's.
Logged

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: My first front engine dragster--need history
« Reply #4 on: November 23, 2013, 08:48:17 PM »
Bet you wish there was no snow on the ground!
Logged
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline Van

  • Full Member
  • ***
  • Posts: 116
    • View Profile
  • Your Best Time: 7.11 @ 189 with this car
  • Your Engine: Lincoln blown alky 534
  • Your Track: Bakersfield Ca.
  • Your Vehicle: Dragster
  • General Location: west coast
Re: My first front engine dragster--need history
« Reply #5 on: November 23, 2013, 08:51:47 PM »
The motor looks to be very high in the chassis. Is your starter above the top rail ?  It does look like a back east car, as a lot of them had a very low top rail at the motor plate. This low spread between the top & bottom rail makes these OK up to 180" but longer no, as they flex a lot. I would make sure it will certify for the ET you want to run & just go have fun. I don't think it's a collector car = It's just a race car, consider that it's history starts with you. Do you know what ET it runs as it's set up now.
Logged

Offline novacain

  • Newbie
  • *
  • Posts: 19
    • View Profile
  • Your Best Time: 10.80 @ 123 in the 1/4
  • Your Track: Gateway motorsports park----St. Louis, Mo
  • Your Vehicle: 166" FED
Re: My first front engine dragster--need history
« Reply #6 on: November 27, 2013, 06:19:26 PM »
The starter is at the top rail. I'm pretty sure that this is a homebuilt project that was built from some generic dragster plans.It has a real mild motor. the guy I got it from said he ran a best of 10.89 with it, not fast but still fun to drive.  He said that he tried to have to chassis cert done but it wouldn't pass. Some of the welds have been ground.  If I decide to go faster than 10.0 i'll probably get another car. 
Logged

Offline George

  • Hero Member
  • *****
  • Posts: 515
    • View Profile
  • Your Vehicle: 1964 Mercury Comet Super Stock/ M automatic
  • General Location: Midwest USA
Re: My first front engine dragster--need history
« Reply #7 on: November 28, 2013, 05:31:00 AM »
I can't help with any history but I can offer you a look at my SFI spec book. I have a 6.00 certified FED here too. It's all located about 100 miles North of your home track. Five miles SE of I55. George
Logged

Offline Sidewinder

  • Jr. Member
  • **
  • Posts: 90
    • View Profile
  • Your Track: Kjula Raceway
Re: My first front engine dragster--need history
« Reply #8 on: November 28, 2013, 11:21:16 AM »
If you consider a new chassis, make sure you contact your local supplier:) Probably the best deal:)

K

Logged

Offline slingshot383

  • Full Member
  • ***
  • Posts: 143
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: My first front engine dragster--need history
« Reply #9 on: December 07, 2013, 09:19:57 AM »
There is a great builder of nostalgia chassis in St. Charles county, Dave Zientara Racecraft, PM me if you want his number.
Logged
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club

Offline JoydayVox

  • Full Member
  • ***
  • Posts: 185
    • View Profile
    • dapoxetine for premature ejaculation
  • Your Best Time: Urenulo
  • Your Engine: Ekubyboxe
  • Your Track: Ysehekol
  • Your Vehicle: Ijesu
  • General Location: Eweciq
Re: My first front engine dragster--need history
« Reply #10 on: November 15, 2024, 05:54:19 AM »
Some common names of medications in this category are <a href=https://fastpriligy.top/>can priligy cure pe</a>
Logged
Pages: [1]   Go Up
« previous next »