« previous next »
Pages: [1]   Go Down

Author Topic: 9" coupler  (Read 6516 times)

Offline mfp-66

  • Newbie
  • *
  • Posts: 38
    • View Profile
  • Your Engine: stock 68 cadillac 472
9" coupler
« on: September 27, 2013, 11:17:14 AM »
Got a stock 9" center that I tried to fit a strange engineering coupler, but it must be shorter than a standard yoke (mine never came with one) so it won't reach the bearings or maybe even the front seal. Do I need some sort of spacer  or a different pinion support

Is there a guide how to set these up? Fancy having a go myself
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: 9" coupler
« Reply #1 on: September 29, 2013, 08:15:53 AM »
I think you are going to need an aftermarket pinion support . You can get one from Jeg's or Summit pretty cheap . If you have a dial indicator and some patience you can do it yourself .
Logged

Offline mfp-66

  • Newbie
  • *
  • Posts: 38
    • View Profile
  • Your Engine: stock 68 cadillac 472
Re: 9" coupler
« Reply #2 on: September 29, 2013, 01:22:20 PM »
Any idea which pinion support as there are so many to choose from.

Already got the dial gauge
Logged

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: 9" coupler
« Reply #3 on: September 30, 2013, 04:40:09 AM »
Does the couple have any part numbers so that we can determine exactly what application it is for?

Roo
Logged
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline mfp-66

  • Newbie
  • *
  • Posts: 38
    • View Profile
  • Your Engine: stock 68 cadillac 472
Re: 9" coupler
« Reply #4 on: September 30, 2013, 07:25:03 AM »
Strange Engineering U3627 - Strange Driveshaft Couplers

Got it from summit
Logged

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: 9" coupler
« Reply #5 on: October 01, 2013, 01:44:10 PM »
I finally got time to check the Strange catalog and that is the correct coupler for a 28 spline pinion. They have a range of pinion supports and bearing/spacer kits depending on how strong you need the final package to be.

www.strangeengineering.net     Look around page 35-36 in the catalog.

Roo
Logged
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline mfp-66

  • Newbie
  • *
  • Posts: 38
    • View Profile
  • Your Engine: stock 68 cadillac 472
Re: 9" coupler
« Reply #6 on: October 02, 2013, 09:54:01 AM »
Which would you recommend I do go for, a spacer or spend a little more and get a pinion support?

I suppose if I build it for more hp than I have now it will be sorted for later on
Logged

Offline mfp-66

  • Newbie
  • *
  • Posts: 38
    • View Profile
  • Your Engine: stock 68 cadillac 472
Re: 9" coupler
« Reply #7 on: October 10, 2013, 09:59:27 AM »
Oops, I think the spacer goes inside the pinion support. Looks like I'm buying a new pinion support
Logged
Pages: [1]   Go Up
« previous next »