Author Topic: blower drive parts  (Read 6304 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
blower drive parts
« on: July 14, 2013, 10:59:05 AM »
Im selling some of my blower drive stuff since I have 3 or 4 of most of them. Ihave some couplers for drive,shafts for snouts,a snout few starter cages and cpl pulleys 24,26,40 probably faster driver than most here will use 40 to 60% od range stuff.Few mag. idler pulleys. Contact me as to what you need.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: blower drive parts
« Reply #1 on: July 14, 2013, 12:17:00 PM »
Im selling some of my blower drive stuff since I have 3 or 4 of most of them. Ihave some couplers for drive,shafts for snouts,a snout few starter cages and cpl pulleys 24,26,40 probably faster driver than most here will use 40 to 60% od range stuff.Few mag. idler pulleys. Contact me as to what you need.
24 tooth pulley?
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: blower drive parts
« Reply #2 on: July 14, 2013, 08:41:14 PM »
yea Glen 24 tooth for when you want to go fast and see how quick you can wear the teflon in blower.I think it was for 66% over. I think we  where in Nebraska at Corky's track middle of summer and crappy air.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: blower drive parts
« Reply #3 on: July 15, 2013, 05:01:43 AM »
It fits over the snout?
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: blower drive parts
« Reply #4 on: July 15, 2013, 08:41:46 AM »
had to trim about .060 off snout. Ever see a PSI at 120% od looks like thimble and wagon wheel pulley's. Plus I like running smallest puleys to get od I wanted since smaller bottom and top that makes same blower speed as two larger ones means less rotating weight.

 Tip. If you drill or maching opening in each groove it will make slight power differance(dyno proven).Theory is getting air from under belt makes it get full contact ansd some how makes od more accurate. Not sure I buy reason I do know two fellas who tested and said 15 to 20 hp gain. Im keeping full set of pulleys because they are machined and most likely other would worry about holes,never had problem.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot