Author Topic: Tyre slip on the Rim  (Read 5903 times)

Offline Rat

  • Jr. Member
  • **
  • Posts: 65
    • View Profile
  • Your Best Time: 8.585 @ 154.55
  • Your Engine: Stack Injected All Iron 392 Chrysler Hemi
  • Your Track: Willowbank Raceway, Queensland, Australia
  • Your Vehicle: Colthup Bros FED
  • General Location: Australia - East Coast
Tyre slip on the Rim
« on: November 28, 2021, 02:24:30 AM »
We are about to fit new tyres on the Halibrands 8) we have, obviously we don't want to use bead screws, any suggestions to help limit tyre slip on the rim. Thanks

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Tyre slip on the Rim
« Reply #1 on: November 28, 2021, 08:19:24 AM »
Clean the tire beads and rims with solvent before pressurizing the slick.
At the suggestion of another altered driver I stopped using bead screws years ago. We don't use tubes. Neither of us have ever had problems.Tire pressures in the 5 - 6 psi range.
It might be interesting to mark the tire and rim to give you confidence.

Offline Rat

  • Jr. Member
  • **
  • Posts: 65
    • View Profile
  • Your Best Time: 8.585 @ 154.55
  • Your Engine: Stack Injected All Iron 392 Chrysler Hemi
  • Your Track: Willowbank Raceway, Queensland, Australia
  • Your Vehicle: Colthup Bros FED
  • General Location: Australia - East Coast
Re: Tyre slip on the Rim
« Reply #2 on: November 29, 2021, 02:27:49 AM »
Thanks Flyer, I was planning on marking the tyre position. Any particular reason for not using tubes.

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Tyre slip on the Rim
« Reply #3 on: November 29, 2021, 03:50:49 AM »
a ton of weight added with tubes.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Tyre slip on the Rim
« Reply #4 on: November 30, 2021, 05:46:10 AM »
Thanks Flyer, I was planning on marking the tyre position. Any particular reason for not using tubes.
Yes
Rotational weight has a much greater effect on performance than static weight in the car. A pound of weight on the tire circumference has about the same effect on performance as ten pounds in the chassis (fun fact: on a bicycle with most of the weight at the outer periphery the ratio is about 16:1.)

Offline JEFF/21C

  • Full Member
  • ***
  • Posts: 122
    • View Profile
  • Your Best Time: N/A
  • Your Engine: 306 SBC INJECTED ALKY
  • Your Track: NONE
  • Your Vehicle: 23 T ALTERED
  • General Location: eastern canada
Re: Tyre slip on the Rim
« Reply #5 on: November 30, 2021, 01:53:25 PM »
help needed How do you run slicks tubeless, sidewalls leak, on dirt we adjusted tire pressure between heats and tires and only lasted one or two races so side wall leakage was no biggy. On the fed we ran tubes  and they were heavy

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Tyre slip on the Rim
« Reply #6 on: November 30, 2021, 03:09:47 PM »
Leakage is an issue. Tire pressure needs to be checked often. I do it every round just before pullout, as do most bracket racers. If you lay a typical slick on its side and wet it down with soapy water and come back an hour later it will be full of suds on the sidewalls. Just the nature of the beast.

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Tyre slip on the Rim
« Reply #7 on: November 30, 2021, 03:17:56 PM »
Also, I block up the axles on my altereds if it will sit for several days.

Also also, in Ford's assembly plants they had a product called "murple" (get it?, it is the only word that rhymes with purple). It was used on hoses and vacuum lines as a lubricant but after installation it dried and acted as an adhesive bonding the rubber to the nipple. I hesitated to mention that initially as I do not know if it is proprietary or available commercially. There may be a similar product on the market.
« Last Edit: November 30, 2021, 03:22:23 PM by THE FRENCHTOWN FLYER »

Offline Frontenginedragsters

  • Full Member
  • ***
  • Posts: 202
    • View Profile
    • Pro-Formance Specialties
Re: Tyre slip on the Rim
« Reply #8 on: November 30, 2021, 05:14:57 PM »
 I'm following this thread.
Most of us are bracket racing. I use tubes because every time I opened the trailer door one or both slicks would be soft or flat.
Tubes fixed that but I'm always wanting to get more out of our stuff.
Thanks: Matt
Driving a Front Engine Dragster builds character and keeps you awake for a 1/4 mile at a time.
http://www.pro-formancespecialties.com/

Offline lake_harley

  • Sr. Member
  • ****
  • Posts: 262
    • View Profile
  • Your Best Time: 7.06 @99.58 - 1/8 mi.
  • Your Engine: Carbureted, gas mild 305 Chevy
  • Your Track: Jeffers Motorsports Park - Sikeston, MO
  • Your Vehicle: 145" FED
  • General Location: SE Missouri
Re: Tyre slip on the Rim
« Reply #9 on: November 30, 2021, 06:21:01 PM »
When I had a dirt track modified we would "paint" the inside of the tire with sealer. Memory is a bit faded, but I believe it was from Berrymans. I don't recall it being 100% effective, but it sure helped. Should work with slicks. The Hoosier tires we were running were so thin you could see the thread's profile in the sidewall.

Lynn

Offline JEFF/21C

  • Full Member
  • ***
  • Posts: 122
    • View Profile
  • Your Best Time: N/A
  • Your Engine: 306 SBC INJECTED ALKY
  • Your Track: NONE
  • Your Vehicle: 23 T ALTERED
  • General Location: eastern canada
Re: Tyre slip on the Rim
« Reply #10 on: December 01, 2021, 07:08:46 AM »
hoosier's were and are what I use ran anti-flat liquide on the dirt tires when I had time never tried it with slicks, alway blocked chassis when towing

Offline BK

  • Sr. Member
  • ****
  • Posts: 310
    • View Profile
  • Your Best Time: 8.45 / 5.30
  • Your Track: Empire Dagway
  • Your Vehicle: Late 70's FED
Re: Tyre slip on the Rim
« Reply #11 on: December 01, 2021, 07:29:18 AM »
With Mickey Thompson tires I used dish soap straight out of the bottle and it made a big difference but was not 100%
With Hoosier slicks I have no problem with leakage without tubes.


Offline tcoupekyle

  • Sr. Member
  • ****
  • Posts: 354
    • View Profile
  • Your Best Time: 4.70 1/8
  • Your Track: Houston Motorsport park
  • Your Vehicle: 225" slip joint FED
  • General Location: Houston
Re: Tyre slip on the Rim
« Reply #12 on: December 02, 2021, 10:25:28 PM »
Same with the dish soap. But it only a temporary thing they still leak.

Offline JEFF/21C

  • Full Member
  • ***
  • Posts: 122
    • View Profile
  • Your Best Time: N/A
  • Your Engine: 306 SBC INJECTED ALKY
  • Your Track: NONE
  • Your Vehicle: 23 T ALTERED
  • General Location: eastern canada
Re: Tyre slip on the Rim
« Reply #13 on: December 03, 2021, 03:58:47 PM »
I only used dish soap to mount tires that didn't have bead locks

Offline e-drag

  • Newbie
  • *
  • Posts: 23
    • View Profile
  • Your Best Time: 6.32 236 1/4mi
  • Your Engine: 468 TFX HEMI
  • Your Track: Barona
  • Your Vehicle: AA/FA
  • General Location: LoCal
Re: Tyre slip on the Rim
« Reply #14 on: December 08, 2021, 11:25:06 AM »
I'm following this thread.
Most of us are bracket racing. I use tubes because every time I opened the trailer door one or both slicks would be soft or flat.
Tubes fixed that but I'm always wanting to get more out of our stuff.
Thanks: Matt
x2