« previous next »
Pages: [1]   Go Down

Author Topic: setup to simply transmission removal  (Read 2896 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
setup to simply transmission removal
« on: October 05, 2021, 07:58:27 AM »
 Well time was I would pull trans in second just to look at something. Never was issue and easy as xxxx. Nowdays the transmissions are getting heavier even after money I spent on aluminum pump,aluminum valve body,lighter case,lighter pan,lighter bolts and anthing else to shave a once off. Either that or I am getting old.Nope thats not it. got to be heavier.

Wondering if any of you have a slick setup for making it easier for us highly mechanical educated fellow to pull trans. Sound better than us old body worn to xxxx from abuse guys.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Frontenginedragsters

  • Full Member
  • ***
  • Posts: 202
    • View Profile
    • Pro-Formance Specialties
Re: setup to simply transmission removal
« Reply #1 on: October 05, 2021, 02:00:05 PM »
That's too bad because my Lenco still weighs the same.  ;D
Logged
Driving a Front Engine Dragster builds character and keeps you awake for a 1/4 mile at a time.
http://www.pro-formancespecialties.com/

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: setup to simply transmission removal
« Reply #2 on: October 05, 2021, 05:37:22 PM »
need a lift handle for 2 spd lenco? I just happen to have one hanging in shop.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline e-drag

  • Newbie
  • *
  • Posts: 23
    • View Profile
  • Your Best Time: 6.32 236 1/4mi
  • Your Engine: 468 TFX HEMI
  • Your Track: Barona
  • Your Vehicle: AA/FA
  • General Location: LoCal
Re: setup to simply transmission removal
« Reply #3 on: October 06, 2021, 03:30:06 PM »
Drop it out the bottom, easy peasy.  Use studs on the block.  Unbolt the converter and zip tie the converter to the trans.  Pull coupler, tb wire and linkage.  Remove nuts from studs, slide the whole thing back and ease it to the ground.  Done!  You can use straps to go around the unit to grip and lower it to the ground.
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: setup to simply transmission removal
« Reply #4 on: October 07, 2021, 03:03:25 PM »
 Studs in block are kind of std on this deal. I have one at top center that is little longer to help plac e it during install. Dropping out bottom not as easy with diaganols in chassis.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: setup to simply transmission removal
« Reply #5 on: October 07, 2021, 03:06:57 PM »
Been trying to design a craddle that will allow me to slide trans back and pisck up or sit dwon and slide forward. Hoping someone had a design I could cheat and work off of.LOL
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline e-drag

  • Newbie
  • *
  • Posts: 23
    • View Profile
  • Your Best Time: 6.32 236 1/4mi
  • Your Engine: 468 TFX HEMI
  • Your Track: Barona
  • Your Vehicle: AA/FA
  • General Location: LoCal
Re: setup to simply transmission removal
« Reply #6 on: October 11, 2021, 05:27:25 PM »
I would lose those diagonals!  Sheldon Gecker gave me the same advise at the winternats one time after watching my pitiful attempt at a quick tranny swap and lifting the dang thing rather than dropping it out the bottom
Logged

Offline slingshot383

  • Full Member
  • ***
  • Posts: 143
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: setup to simply transmission removal
« Reply #7 on: November 26, 2021, 06:16:32 AM »
I second lose that diagonal, wrong place for it, in the bay behind the transmission is OK, but not where you want to drop the tranny, unless it is removable style.
Logged
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: setup to simply transmission removal
« Reply #8 on: February 28, 2022, 07:33:49 PM »
My diagnols are removable and they are behind trans enough to allow dropping past them. They are issue with building a cradle.  Picking up is easier than wrestling down and out. Plus crossbar is bolted in and flips to right with one quick pin.

Yes been a while since I checked thread/
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot
Pages: [1]   Go Up
« previous next »