« previous next »
Pages: [1]   Go Down

Author Topic: wheel disc  (Read 3340 times)

Offline grapro

  • Jr. Member
  • **
  • Posts: 71
    • View Profile
  • Your Track: edmonton
  • Your Vehicle: 184" FED
wheel disc
« on: March 05, 2021, 09:51:23 AM »
I just bought a aluminum wheel disc for my front wheels and was wondering what was the best way to mount it. There are 3 small clips with it, do they get riveted on on what is the proper way?
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: wheel disc
« Reply #1 on: March 05, 2021, 03:45:05 PM »
Call Jon at Hayden wheels or might get him here if he does not chime in.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline BK

  • Sr. Member
  • ****
  • Posts: 310
    • View Profile
  • Your Best Time: 8.45 / 5.30
  • Your Track: Empire Dagway
  • Your Vehicle: Late 70's FED
Re: wheel disc
« Reply #2 on: March 05, 2021, 04:14:48 PM »
Mine were riveted over spokes. On the right side.
Logged

Offline sknopp

  • Newbie
  • *
  • Posts: 41
    • View Profile
  • Your Best Time: 7.008@215 on 7.00 Index
  • Your Track: Bowling Green
  • Your Vehicle: 1969 MW 214" FED
Re: wheel disc
« Reply #3 on: March 09, 2021, 09:20:00 AM »
Mine was fastened in 3 places, equally spaced.  An stainless steel strap about 1/4" wide, maybe 3/4" long and 1/16" thick went around a spoke and was riveted to the disc using 2 rivets.  I took it off many years ago because I thought it looked better without.  I think the staging beam heights are pretty stand now so you probably don't need it as far as function is concerned.  I was at a car show once and a guy wanted to know why I only had a hubcap on one side!
Steve K.   
Logged

Offline JEFF/21C

  • Full Member
  • ***
  • Posts: 122
    • View Profile
  • Your Best Time: N/A
  • Your Engine: 306 SBC INJECTED ALKY
  • Your Track: NONE
  • Your Vehicle: 23 T ALTERED
  • General Location: eastern canada
Re: wheel disc
« Reply #4 on: March 09, 2021, 04:05:37 PM »
We have wire wheels and used tie wraps to hold nylon disc in place
Logged

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: wheel disc
« Reply #5 on: March 18, 2021, 04:11:20 PM »
I sell wheel disks with alum straps for ataching around the spokes with either pop rivits or small bolt and nylock. We have raced without a staging disk of 10 years , but then again I built some 18" wire spoke wheels with 2.00x18 MC road race tires with a Akront rim that has a bit of a lip on the rim, so we never redlighted UNTIL we raced Phoenix for the 1'st time . Turns out they set their staging beams a little higher, enough so the JF cars with litle disks didn't redlite, but all the cars without staging disks did redlite, so since then we run a black light disk.
Good luck
Jon   
Logged
Jon C. Hansen

Hayden Wheels

Offline grapro

  • Jr. Member
  • **
  • Posts: 71
    • View Profile
  • Your Track: edmonton
  • Your Vehicle: 184" FED
Re: wheel disc
« Reply #6 on: March 21, 2021, 04:56:18 PM »
Thanks   I got your wheel disc from S and W . I hope it will help.
Logged
Pages: [1]   Go Up
« previous next »