« previous next »
Pages: [1]   Go Down

Author Topic: ATi vs Reid PG case  (Read 4885 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
ATi vs Reid PG case
« on: October 12, 2020, 02:30:41 PM »
Going to have to get a legal transmission case. FI is out of stock. Jegs has cpl two piece as does summit. Trying to see if both have a BBM bell I can change out, Beats xxxx out of mid plate as adapter. Loosing 14lbs when swapping out this JW does not hurt anything,

Any real difference in ATI which summit has and Reid which jegs has?
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline BK

  • Sr. Member
  • ****
  • Posts: 310
    • View Profile
  • Your Best Time: 8.45 / 5.30
  • Your Track: Empire Dagway
  • Your Vehicle: Late 70's FED
Re: ATi vs Reid PG case
« Reply #1 on: October 12, 2020, 05:38:07 PM »
The one difference I do know of is Reid has an adjustment for the brake release. You can take some of the initial hit out of it.
Logged

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: ATi vs Reid PG case
« Reply #2 on: October 12, 2020, 11:06:12 PM »
In our jrfuel car we use a Reed case because we race heads up .05 pro tree NHRA Heritage and NHRA Comp Elim .06 full tree , so we can adjust [ slow down] the release of the brake.
We just have to get it creditied, every 3 or 5 years.
Logged
Jon C. Hansen

Hayden Wheels

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: ATi vs Reid PG case
« Reply #3 on: October 15, 2020, 08:30:18 PM »
They are all pretty much thesame minus the dump restrictor that Reid has.
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: ATi vs Reid PG case
« Reply #4 on: October 24, 2020, 06:44:55 AM »
dump restrictor? Is that what the bolt on rear of JW is.It is to upper left of case. Not issue if running box but can see where could help if no box. But heck old guys rarely need to slow down reaction times. LMAO
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: ATi vs Reid PG case
« Reply #5 on: October 25, 2020, 06:27:02 PM »
Yes JW has one as well
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: ATi vs Reid PG case
« Reply #6 on: October 27, 2020, 09:46:06 AM »
Same question on DRR and lot f comments about ATI haveing issue with park setup and disengaging at time. Looking like Reid from comment I have gotten so far. Problem is in finding one available.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline gordon

  • Newbie
  • *
  • Posts: 43
    • View Profile
  • Your Track: Sacramento
  • Your Vehicle: FED
Re: ATi vs Reid PG case
« Reply #7 on: November 07, 2020, 11:20:02 AM »
My vote always goes to Reid. I have known Dennis many years, dating back to when he was making his Dedenbear delay boxes in his garage. I worked for ATO transmissions back when his PG case was first being planned . We did a lot of testing of the prototype on our test stand and shop racecars before it was available to public. It is the original and still the best in my opinion. Dennis now offers race cases for the TH400 and 4L80 transmission as well , working closely with Jim Galatioto of ATO for testing and prototype development . Dennis's stuff is like the old Curtiss Mathis TV's, "The quality goes in, before the name goes on". Am I biased? You bet I am! I still get pulled into ATO to do special projects . New Chrysler trans parts should be available after the first of the year from ATO. I really wish any serious racer could have the time to visit with Jim at ATO transmissions. His shop is similar to that found in the F1 world.
Logged
Pages: [1]   Go Up
« previous next »