Author Topic: Chassis jig  (Read 4010 times)

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Chassis jig
« on: March 01, 2020, 06:32:49 AM »
Chassis table with jigs and fixturing to build  FED's, altereds and RED's.  Modular in design the main table is 13' long by 36" wide and weighs over 1000 pounds.  It features 40 numbered holes down the outer rails for the included tooling.  With the included extensions I've built cars to 270".  This table could easily be used to build door cars if you wanted to make some tooling for it.  Machined flat top surface. Also comes with setup notes and whatever little tools and gizmos I've made for it over the years.  Formerly the chassis Dragster Supply/David Beard race cars chassis table.  Pics to come.  $5500.00. This table could be set up and building cars whithin a couple hours of getting it home.  Call or text David @603-234-9496

Offline Supercat

  • Sr. Member
  • ****
  • Posts: 252
    • View Profile
  • Your Best Time: 6.16 @ 218 1/4
  • Your Track: Bakersfield to Bowling Green to New England dragway
  • Your Vehicle: Buick powered/ 200" Fastech FED
Re: Chassis jig
« Reply #1 on: March 01, 2020, 02:19:24 PM »
David what town are you located in?
John

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Chassis jig
« Reply #2 on: March 01, 2020, 02:55:04 PM »
David what town are you located in?
John

Merrimack NH

Offline Supercat

  • Sr. Member
  • ****
  • Posts: 252
    • View Profile
  • Your Best Time: 6.16 @ 218 1/4
  • Your Track: Bakersfield to Bowling Green to New England dragway
  • Your Vehicle: Buick powered/ 200" Fastech FED
Re: Chassis jig
« Reply #3 on: March 01, 2020, 03:20:34 PM »
What's the best time to call tomorrow?
I'm in central Maine and will call with a few questions.

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Chassis jig
« Reply #4 on: March 01, 2020, 03:42:19 PM »
What's the best time to call tomorrow?
I'm in central Maine and will call with a few questions.

After 2:30 is best.  Or until 9 tonight
« Last Edit: March 01, 2020, 03:48:35 PM by fuel749 »

Offline Supercat

  • Sr. Member
  • ****
  • Posts: 252
    • View Profile
  • Your Best Time: 6.16 @ 218 1/4
  • Your Track: Bakersfield to Bowling Green to New England dragway
  • Your Vehicle: Buick powered/ 200" Fastech FED
Re: Chassis jig
« Reply #5 on: March 01, 2020, 03:48:42 PM »
Ok. Call you then

Offline buickfed

  • Full Member
  • ***
  • Posts: 191
    • View Profile
Re: Chassis jig
« Reply #6 on: March 02, 2020, 03:12:01 PM »
david,
are you retiring from the business?
john
the other buick dragster

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Chassis jig
« Reply #7 on: March 02, 2020, 05:14:33 PM »
david,
are you retiring from the business?
john
the other buick dragster

Yes, had an offer to good to refuse. So I didn't.

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Chassis jig
« Reply #8 on: April 04, 2020, 06:55:37 AM »
Worked up a list of stuff that's included with this jig:

 MW alignment bar with rings for BBC, SBC, early and late Chrysler.

SBC and BBC and 426 mock up blocks (BBC and 426 are aluminum)

powerglide case cut to fit over alignment bar

Autocad DXF files for various brackets and tabs required to build chassis...rear end housing mounts, anti rotation mounts, chute mounts and levers, motor plates, steering box mounts etc etc