Author Topic: pump rebuild  (Read 3366 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
pump rebuild
« on: June 20, 2019, 07:00:40 PM »
Spud,

Have question.I have a 1100 in need of repair.Can it be built to a lower gpm pump. Looking to get it down to around 11 gpm or so.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: pump rebuild
« Reply #1 on: June 21, 2019, 10:01:56 AM »

 It could be done, but it would be pretty expensive. A new Enderle 760 lid, gear, rotor and end piece would be almost as much as a new 760 pump.

 Spud

 

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

dreracecar

  • Guest
Re: pump rebuild
« Reply #2 on: June 21, 2019, 04:26:05 PM »
Current A/F Nitro big pump has a restrictor installed to get it down to 11.whatever gpm @ 8000 crank rpm

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: pump rebuild
« Reply #3 on: June 30, 2019, 07:26:59 AM »
Thanks. Did not know a restrict-or was allowed,but that would save me pretty good amount and be able to use cpl pumps I have. Not that I plan to go A/fuel event wiser,but maybe play some later and get some good working knowledge of setup.

So Spud .Would I still be better off dropping these down closer when rebuilding them and then have restrictor .Figure no reason running a ton of head pressure if don't have to.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

dreracecar

  • Guest
Re: pump rebuild
« Reply #4 on: July 03, 2019, 07:41:19 PM »
A/F (NITRO) fanagled the big pump/restrictor to give them more volume at the hit without adding pump speed. Running the new "BUBBA" tire was creating too much load for the small amount of fuel volume of the normal pump. This change alone got them from the low 6's into the upper 5's

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: pump rebuild
« Reply #5 on: July 05, 2019, 07:48:59 AM »
any idea as to how big of pump they are using? Going to check with cpl folks about this and getting  restrictor in one of my older pumps . I know they use to be right at 18.5 gpm,but may need work. May give Spud a call next week.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

dreracecar

  • Guest
Re: pump rebuild
« Reply #6 on: July 05, 2019, 09:11:14 AM »
. Fuel pump for blown alcohol restricted to a total fuel delivery limited to 9.60 gpm at 4,000 rpm pump speed measured at 100 psi. Fuel pump for injected nitro restricted to a total fuel delivery limited to 11.60 gpm at 4,000 rpm pump speed measured at 100 psi. All competitors must submit their fuel pump(s) to the NHRA-accepted testing facility (KJ Crawford Inc. Fuel Injection; phone, 707-542-9551) for certification prior to competition