Author Topic: Wheelie Bars  (Read 5202 times)

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Wheelie Bars
« on: September 08, 2019, 06:39:25 PM »
I have a 200" fed, 6.0 cert moly car, plan on running 7.60's or better. Want to build wheelie bars, have a few questions and would like any pictures possible. It is a three bar single wheel deal on there now but is bent badly. Would like to know what size and thickness for the bars. It is roughly 6' long on the top bars and 6 1/2' on the bottom bar. The bottom bar mounts just under the back of the seat on the bottom of the car as it sits now, top bars on rear of car. What does everyone use for height adjustment? Need all new parts and where to buy like adjuster and wheel with brackets? Finally going full steam ahead on putting car together after life getting in the way for too long. Thanks Greg.
If it jams force it, if it breaks it needed replaced anyways

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Wheelie Bars
« Reply #1 on: September 08, 2019, 07:08:57 PM »
I have seen this on several cars for cool

https://neilparks.com/adjustable-wheelie-bar.html

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: Wheelie Bars
« Reply #2 on: September 09, 2019, 04:21:16 AM »
For the wheel end I use a package that I get from McKinney which has the same components as used on a lot of the big show fuel cars. It has a tool less quick adjustment deal. On my bars I use 1.25" uppers and 1"-1.125" lower tubes with a quick pin to allow the wheel to be raised quickly for towing. I tie the upper bars together with a cross tube which is welded to sleeves retained with stop rings--that way there are no welds (other than the tacks on the stop rings) apart from those on each end of the main tubes. At the attachment points to the frame I use cut down bolts with a clevis pin rather than nuts so that the bar can be removed without tools at the end of the day.
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: Wheelie Bars
« Reply #3 on: September 09, 2019, 05:45:15 AM »
What wall thickness do you use Rooman? Thanks
If it jams force it, if it breaks it needed replaced anyways

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: Wheelie Bars
« Reply #4 on: September 09, 2019, 08:18:49 AM »
Generally .058"  PM me your e mail address (or cell #) and I will send you some photos. The files are too big to post here.

Roo
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Wheelie Bars
« Reply #5 on: September 09, 2019, 09:10:17 AM »
Generally .058"  PM me your e mail address (or cell #) and I will send you some photos. The files are too big to post here.

Roo

Roo, out of curiosity do you build a shorter bar for cars with clutches. I am noticing quite a few of the clutch cars run pretty short bars compared to what I have seen with automatics

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: Wheelie Bars
« Reply #6 on: September 09, 2019, 01:43:25 PM »
None of my recent customers have had clutch cars apart from the dragster that I am getting ready to ship to New Zealand and it has my standard package. I am also building a fuel altered that has a clutch but I am planning to put the same bar on it as I normally use.

Roo
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Wheelie Bars
« Reply #7 on: September 09, 2019, 05:53:00 PM »
I am thinking I should change mine it’s a really long bar 7’ long made from 1” .058

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: Wheelie Bars
« Reply #8 on: September 10, 2019, 03:36:44 AM »
I am thinking I should change mine it’s a really long bar 7’ long made from 1” .058

Does it do the job? If so I can't see a reason to change it.

Roo
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Wheelie Bars
« Reply #9 on: September 10, 2019, 03:24:37 PM »
Yes it works but some people watching my car tell me it flexes a ton and may cause problems later.