Author Topic: water or not  (Read 10023 times)

Offline xlr8

  • Newbie
  • *
  • Posts: 28
    • View Profile
    • JEFF CHANDLER MATCO TOOLS
  • Your Best Time: 7.99 1/4 mile 166 mph
  • Your Engine: Pontiac Alcohol 428
  • Your Track: BARONA
  • Your Vehicle: 190" FED
  • General Location: west coast
Re: water or not
« Reply #15 on: April 08, 2019, 11:22:57 AM »
You guys are the greatest source of info! Thank you. What type of temperature sensor is used with no water?
Jeff Chandler - Matco Tools
619-991-7845
xlr8jsc@cox.net

Offline glofria

  • Full Member
  • ***
  • Posts: 138
    • View Profile
  • Your Best Time: 7.323 @ 185.05
  • Your Engine: A blown 388 c.i. Small Block Chevy
  • Your Track: Auto Club Famoso Raceway
  • Your Vehicle: An original 1957 Chevy Bel-Air
  • General Location: Southern California
Re: water or not
« Reply #16 on: April 08, 2019, 01:36:54 PM »
Again it would depend on if you are injected or blown. At you running it outright or on an index?

For our blown application we are looking between 1000 to 1100 degrees, which reminds me that we have our chamber and exhaust runner ceramic coated to better deal with the heat.

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: water or not
« Reply #17 on: April 09, 2019, 05:22:33 AM »
You guys are the greatest source of info! Thank you. What type of temperature sensor is used with no water?

 I use electric gauge that has a sensor tapped into head.Would think you can do same in block.Does not require being in water jacket are, I also had 4 sensor working on same gauge using 2 3 position switches. I read oil,trans ,left and right head temps. Hardest part is remembering which switch in what position reads what. label printers where made for old guys.LOL
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline xlr8

  • Newbie
  • *
  • Posts: 28
    • View Profile
    • JEFF CHANDLER MATCO TOOLS
  • Your Best Time: 7.99 1/4 mile 166 mph
  • Your Engine: Pontiac Alcohol 428
  • Your Track: BARONA
  • Your Vehicle: 190" FED
  • General Location: west coast
Re: water or not
« Reply #18 on: April 15, 2019, 11:06:47 AM »
You guys are the greatest source of info! Thank you. What type of temperature sensor is used with no water?

 I use electric gauge that has a sensor tapped into head.Would think you can do same in block.Does not require being in water jacket are, I also had 4 sensor working on same gauge using 2 3 position switches. I read oil,trans ,left and right head temps. Hardest part is remembering which switch in what position reads what. label printers where made for old guys.LOL

This car is injected alky, no blower. Where can I find those temp sensors that work on the block or heads without water? What brand are they?
Jeff Chandler - Matco Tools
619-991-7845
xlr8jsc@cox.net

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: water or not
« Reply #19 on: April 15, 2019, 11:44:07 AM »
autometer has them and I find them on ebay most of the time. They have two styles, One had a probe that protrudes past threaded part and one that is just the threads. Cylinder head temp sending unit and make sure short or long sweep matches gauge you are using. I think about 15 bucks per unit on ebay. They have cpl listed now.

Like stated if you want multiple points you can wire in 3 position switch with middle pole to gauge and upper to one sending unit and lower to another unit. Flip back and forth between two readings.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot