« previous next »
Pages: 1 2 [3]   Go Down

Author Topic: Budget rail  (Read 15750 times)

dreracecar

  • Guest
Re: Budget rail
« Reply #30 on: January 16, 2019, 03:50:46 PM »
You can go online to Aircraft Spruce and look at there tubing charts for material. Good prices and consider you basicly buy by foot so you dont have to buy the full length--only what you need, They have a east coast outlet in Georgia. A 225" SFI spec car Im doing now , I have about $1000 in tubing
Logged

Offline Kentucky Mark

  • Newbie
  • *
  • Posts: 15
    • View Profile
  • Your Best Time: 12.90
  • Your Engine: 327 sb Chevrolet
  • Your Track: Edgewater
  • Your Vehicle: 1987 Oldsmobile Cutlass
  • General Location: Midwest
Re: Budget rail
« Reply #31 on: January 16, 2019, 04:42:45 PM »
It was a Mickey Thompson dragmaster chassis!and it belongs to Dave Huber Rooman knows his stuff! Could you build that chassis and have it NHRA legal? If wearing y'all with these questions I appologize but appreciate the input
Logged

Offline AF150

  • Jr. Member
  • **
  • Posts: 92
  • The Devil is in the Details
    • View Profile
  • Your Best Time: 7.37 1/4 mile
  • Your Engine: Early Hemi, 365", Blown Alky
  • Your Track: Tulsa Raceway Park
  • Your Vehicle: 200" FED
Re: Budget rail
« Reply #32 on: January 17, 2019, 08:00:14 AM »
Don't forget to get the SFI book. No sense building something that won't certify.
Logged
MB

dreracecar

  • Guest
Re: Budget rail
« Reply #33 on: January 17, 2019, 09:24:23 AM »
Quote from: Kentucky Mark on January 16, 2019, 04:42:45 PM
It was a Mickey Thompson dragmaster chassis!and it belongs to Dave Huber Rooman knows his stuff! Could you build that chassis and have it NHRA legal? If wearing y'all with these questions I appologize but appreciate the input

  Best to get in touch with the NHRA Chassis tech inspector for your area to answer that question before moving forward. He will guide you since the design you are after is not shown in the SFI spec book and you may be restricted to 10sec or slower
Logged

Offline jeff/21

  • Full Member
  • ***
  • Posts: 186
    • View Profile
  • Your Best Time: 8.24
  • Your Track: any with-in a 6hr radius
  • Your Vehicle: fed
Re: Budget rail
« Reply #34 on: January 19, 2019, 08:14:22 AM »
simple answer is yes it can be built from mild steel ERW (cheap)the car will be heavier as the SFI spec is for thicker wall tubing
SFI book will answer a lot of questions
Logged

dreracecar

  • Guest
Re: Budget rail
« Reply #35 on: January 19, 2019, 08:48:36 AM »
current mild steel tubing wall is undersize for the spec and will not pass if the car must be stickered
Logged

dreracecar

  • Guest
Re: Budget rail
« Reply #36 on: January 19, 2019, 11:21:25 AM »
old school
Logged

Offline Kentucky Mark

  • Newbie
  • *
  • Posts: 15
    • View Profile
  • Your Best Time: 12.90
  • Your Engine: 327 sb Chevrolet
  • Your Track: Edgewater
  • Your Vehicle: 1987 Oldsmobile Cutlass
  • General Location: Midwest
Re: Budget rail
« Reply #37 on: January 20, 2019, 04:19:15 PM »
Thanks for the info
Logged

Offline speedbump

  • Newbie
  • *
  • Posts: 16
    • View Profile
  • Your Best Time: n/a
  • Your Track: e-town lebbaon valley
  • Your Vehicle: fed
Re: Budget rail
« Reply #38 on: February 18, 2019, 04:08:08 PM »
Welcome back to the sport. If your planning on a fed. 9" ford or Mopar will be more then sufficient. The mopar would probable cost less. Biggest item of concern is to build your cage area wide, 20-21" at the shoulders. This will be one of your biggest resale issue if you ever want to sell in further. Just buy the book for the sfi chassis that you may want to run. or have some one build you the chassis so they can fit mtr. trans and rear in properly. well good luck and enjoy yourself.
Logged

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: Budget rail
« Reply #39 on: February 18, 2019, 05:04:40 PM »
When you are ready for front wheels and tires, I may have some trade-ins on a deal.
Good Luck with your project I would advice you to listen Bruce Dyda, and Rooman
Jon Hansen, Hayden Wheels, 800-624-3803
Logged
Jon C. Hansen

Hayden Wheels
Pages: 1 2 [3]   Go Up
« previous next »