« previous next »
Pages: [1]   Go Down

Author Topic: CONVERTER ID HELP  (Read 3406 times)

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
CONVERTER ID HELP
« on: December 04, 2018, 09:07:43 AM »
Scored an unknown 8 inch--well built--only stampings are on the center of the nose where it goes into crank it says
B26
2936
3
Just was not sure what company stamped them there --just working to ID this thing
Thanks for the help!!!!!!!!!!!!!!
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: CONVERTER ID HELP
« Reply #1 on: December 04, 2018, 01:58:35 PM »
Well,do you know what type of trans it fits? GM? Ford? Three bolt flanges or 4-bolt? What is the pilot diameter size? Spline cpunt?
Logged

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: CONVERTER ID HELP
« Reply #2 on: December 04, 2018, 02:00:10 PM »
Quote from: THE FRENCHTOWN FLYER on December 04, 2018, 01:58:35 PM
Well,do you know what type of trans it fits? GM? Ford? Three bolt flanges or 4-bolt? What is the pilot diameter size? Spline count?
Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: CONVERTER ID HELP
« Reply #3 on: December 04, 2018, 03:15:08 PM »
Yea i know it is 8 in PG spline for Chevy that was not my question
I wanted to know what converter company stamped the numbers on the Hub--that way I can contact them about the inner workings
It is stamped on the center of the hub not on converter body like many--that has to be a "tell" of some certain company
Thanks
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: CONVERTER ID HELP
« Reply #4 on: December 05, 2018, 07:20:45 PM »
Wow what a strange place to stamp a converter, I dont know of any of the major companies that stamp there.
Logged
Pages: [1]   Go Up
« previous next »