« previous next »
Pages: [1]   Go Down

Author Topic: fORD 9" full floater  (Read 3512 times)

Offline DNCMOTORS

  • Newbie
  • *
  • Posts: 6
    • View Profile
  • Your Best Time: NONE
  • Your Engine: 540 BBC
  • Your Track: BREMERTON RACEWAY/ SEATTLE INTERNATIONAL RACEWAY
  • Your Vehicle: 200" FED
  • General Location: WEST COAST
fORD 9" full floater
« on: November 26, 2018, 12:48:21 PM »
Just looking for some basic advice to get started.  Having David Beard finishing my new 200" FED.  I choose a full floater 9" rearend, because I'm comfortable with them from dirt car racing.  Question: Aluminum or steel third member housing?  Do I install the plugs to keep the oil inside the center section?  Any good advice or lessons learned from full floaters?
Thanks
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: fORD 9" full floater
« Reply #1 on: November 26, 2018, 02:26:09 PM »
aluminum third member is fine and shaves about 20 lbs..Ran them for years in Top Alcohol cars. Get the bolt thru style and if me I would get the 3.875 bore. Make sure you can fit 9.5 gear in it as option later if want. If available get drilled axles,not sure they are for floaters .
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline rooman

  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: fORD 9" full floater
« Reply #2 on: November 27, 2018, 04:06:22 AM »
Strange has a gun drilled option for their floater axles.

Roo
Logged
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: fORD 9" full floater
« Reply #3 on: November 27, 2018, 09:42:45 AM »
I run Mark Williams gun drilled 40 spline floater axles in my car
Logged

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: fORD 9" full floater
« Reply #4 on: December 04, 2018, 10:55:14 PM »
I agrre alum, never broke or chracked in 20 years of racing a FED,  steel if you are racing a heavy door car, not  FED.
Logged
Jon C. Hansen

Hayden Wheels
Pages: [1]   Go Up
« previous next »