« previous next »
Pages: [1]   Go Down

Author Topic: starting point leanout  (Read 3049 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
starting point leanout
« on: October 15, 2018, 04:20:37 PM »
Spud,

 Have a edumactated guess of starting point for leanout thats open during stage with SLE and 2 step. 6.85 gpm @100# DSR pump,Enderle K style BV,130 main .036 nozzles  using electric over air solenoid. 482 ci hemi close to 1000 hp. My guess is .070 or close. Oh yea stage rpm 4200 starting point.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: starting point leanout
« Reply #1 on: October 15, 2018, 06:32:09 PM »
I am curious why are your running an SLE and 2-step?
Logged

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: starting point leanout
« Reply #2 on: October 16, 2018, 09:16:47 AM »

 You might end up at a .070 but I sure wouldn't start there. A .060 should be safe and then lean from there.

 Spud
Logged

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline BK

  • Sr. Member
  • ****
  • Posts: 310
    • View Profile
  • Your Best Time: 8.45 / 5.30
  • Your Track: Empire Dagway
  • Your Vehicle: Late 70's FED
Re: starting point leanout
« Reply #3 on: October 16, 2018, 01:18:41 PM »
A .060 - .070 sound awfully big.  Are they that size because the RPM is low.
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: starting point leanout
« Reply #4 on: October 16, 2018, 02:53:47 PM »
sle allows me to throw it wideopen on first or second bulb and two step allows it to come to set point unti trans brake is released by delay box. Not sure How I am going to like sle as I have always just timed it to hit throttle and allow to maybe bump two step before leaving but not on it for full 1.1-- seconds before hitting tires. I know to average folks 1.1 seconds sounds like nothing but in our world its about same as cpl days.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline BK

  • Sr. Member
  • ****
  • Posts: 310
    • View Profile
  • Your Best Time: 8.45 / 5.30
  • Your Track: Empire Dagway
  • Your Vehicle: Late 70's FED
Re: starting point leanout
« Reply #5 on: October 17, 2018, 02:36:51 PM »
My delay box allows me to stage with my foot to floor and I had it set to put it on the 2 step .50 sec before the brake release.
Logged
Pages: [1]   Go Up
« previous next »