« previous next »
Pages: [1]   Go Down

Author Topic: old a/c coil as cooler  (Read 3245 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
old a/c coil as cooler
« on: October 07, 2018, 02:38:02 PM »
I have old a/c coil that we used for cooler wat back.It worked bACK then I am guessing,no data recorders. Any reason not to use it like restriction,too little cooling or any to harm trans. Planning to use for cpl weekends and replace before next year. Maybe few races. If theres chance it could fubar any parts I'll make another cash stretch for better piece.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: old a/c coil as cooler
« Reply #1 on: October 08, 2018, 05:45:05 AM »
My only concern would be an orifice in one end or the other. As long as it has good flow it should work. After all its just a heat exchanger.
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: old a/c coil as cooler
« Reply #2 on: October 08, 2018, 07:00:30 AM »
I have 6 an fittings in 3/8 pipe taps so that should not be issue.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: old a/c coil as cooler
« Reply #3 on: October 08, 2018, 07:02:50 AM »
whats pressure on cooling circuit? Running ATI aluminum pump,deep pan and #6 hose to and from,if any of that matters. Regular braided hose should be fine? Could do PTFE if any chance of blwing line. Not looking to repeat slick in high gear thing like Bristol 91 with Funny car. Sry no laughter.
« Last Edit: October 08, 2018, 09:25:50 AM by wideopen231 »
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline BK

  • Sr. Member
  • ****
  • Posts: 310
    • View Profile
  • Your Best Time: 8.45 / 5.30
  • Your Track: Empire Dagway
  • Your Vehicle: Late 70's FED
Re: old a/c coil as cooler
« Reply #4 on: October 09, 2018, 02:12:01 AM »
PTFE would be the preferred hose but I've run rubber braided without any issues.
I cant help much on the pressure question but I don't think its as high as the internal pressure.
Logged
Pages: [1]   Go Up
« previous next »