« previous next »
Pages: [1]   Go Down

Author Topic: trans temp sensor location  (Read 3021 times)

Offline noslin

  • Sr. Member
  • ****
  • Posts: 259
    • View Profile
  • Your Best Time: 0.00
  • Your Engine: none
  • Your Track: none
  • Your Vehicle: none
  • General Location: west coast
trans temp sensor location
« on: September 24, 2018, 08:42:46 PM »
I want to put a trans temp sensor on the FED.  would i take the temp on the in or out location?   its a powerglide.

thank you
dean
Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: trans temp sensor location
« Reply #1 on: September 25, 2018, 06:45:39 AM »
Usually they are put in the pan
After you have it a few weeks you will have all the info you need---Trans never gets really hot unless you are on the transbrake--after a few runs and you get on the brake temps can climb 100 degrees a second but the instant you let go of the button it falls like a rock back to normal range---temp usually stays pretty stable --it does show you how you can kill one by staying on the converter or brake too long--it will "train" you fast! After that take it out and sell it
That is what most do
If you are bracket racing it shows you how if lucky enough to be in round 6 or 7 --by then you are at a Transmission BBQ
for sure
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: trans temp sensor location
« Reply #2 on: September 25, 2018, 07:31:59 AM »
X2 on what dusterdave said.

On my altereds my trans used to get hot enough for smoke to come out the breather if I went a few rounds. I got in the habit of pouring a 3-gallon jug of water over the PG after a run.

Then I upgraded to a Hayden cooler at the back of the car with a small fan (similar to the ones used on boats for a bilge exhaust and also on NASCAR stock cars for brake cooling). At the entrance to the cooler [the exit side of the trans] I installed a temp sensor that triggers the fan to come on (thru a relay) at 155*F. I also have a dash-mounted over-ride switch to run the fan continuously if need be that I usually use for the final round after the semi's.
When I do my burnout the fan is off. After a run when I drive up the return road the fan comes on. Works great.


Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: trans temp sensor location
« Reply #3 on: September 25, 2018, 04:02:22 PM »
mine is in pan at drain plug. I have it hooked to temp gauge that is also hooked to oil temp and both heads. I use 3 position switches,1 for heads and one for fluids. can rad all 4 with one gauge. just make sure one is off when checking  temps using other switch.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: trans temp sensor location
« Reply #4 on: September 25, 2018, 07:30:43 PM »
Most generally the temp sensor gets installed in the pan as close to the floor of the pan as possible.
Logged
Pages: [1]   Go Up
« previous next »