« previous next »
Pages: [1]   Go Down

Author Topic: Filter for MFI  (Read 4528 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Filter for MFI
« on: April 06, 2018, 07:17:42 PM »
 Going to get filter to run on MFI in FED. New system I am working on uses small nozzles,which will not take much of anything to plug. Never been huge fan of filter when we ran blower motor,because tune up was on edge and any restriction would have pushed it over. Then never ran as small of nozzles and pulled system dwon every week to check for anything and clean.

 What filer are you using and before or after pump.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Filter for MFI
« Reply #1 on: April 06, 2018, 09:17:52 PM »
I run one of these prior to the barrel valve and check it every other pass

http://www.rbssuperchargers.com/Products/Fuel_Filter_Inline_-6_Thru_-16--2600%2D0019
Logged

Offline nostalgic371

  • Newbie
  • *
  • Posts: 26
    • View Profile
  • Your Best Time: tbd
  • Your Engine: none
  • Your Track: none
  • Your Vehicle: none
  • General Location: socal
Re: Filter for MFI
« Reply #2 on: April 07, 2018, 09:13:06 AM »
Quote from: Paul New on April 06, 2018, 09:17:52 PM
I run one of these prior to the barrel valve and check it every other pass

http://www.rbssuperchargers.com/Products/Fuel_Filter_Inline_-6_Thru_-16--2600%2D0019
Are you running a -8 then? Does it effect your tune up in any way?
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Filter for MFI
« Reply #3 on: April 07, 2018, 09:20:04 AM »
Yes I run the -8 and I did not see any difference in my tune up.  One thing though doubt I could see a difference in my tune up any way as I run my car very fat!
Logged

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Filter for MFI
« Reply #4 on: April 25, 2018, 06:11:18 PM »

 The little cone filters are great. I couldn't believe that they didn't restrict flow so I bought a -8 and tested it on the flow bench. 18 GPM through it transparently with no trouble at all. Forward, backwards, no diff. BUT...they won't hold hardly any debris before they start to restrict. So, just be sure to check it often.

 Spud
Logged

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Filter for MFI
« Reply #5 on: April 25, 2018, 06:16:10 PM »
Not sure how legit,was on internet. I watched video of someone testing little cone style and seems he found about .5 or .7 loss for a 13 gpm system.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Filter for MFI
« Reply #6 on: April 25, 2018, 08:13:05 PM »

 Maybe it was a -6?

 Spud
Logged

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: Filter for MFI
« Reply #7 on: April 26, 2018, 09:07:55 AM »
I run one of FIE's 5-6" inch long -08 filter can.  Been there for years. LOTS of filter surface.  I never get debris in it, but i'm super weird about my fuel system too.
Logged
Greg
El Dorado County, CA
www.meansracing.com

Offline noslin

  • Sr. Member
  • ****
  • Posts: 259
    • View Profile
  • Your Best Time: 0.00
  • Your Engine: none
  • Your Track: none
  • Your Vehicle: none
  • General Location: west coast
Re: Filter for MFI
« Reply #8 on: April 26, 2018, 08:00:54 PM »
Greg, what micron screen are you using?   i have couple kinsler filters but they are -10 in/out that i had on my other car for meth.
Logged

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: Filter for MFI
« Reply #9 on: April 27, 2018, 09:30:42 AM »
Quote from: noslin on April 26, 2018, 08:00:54 PM
Greg, what micron screen are you using? 

Spud?  Can you answer that? i'm not sure.  Its what he recommended.
Logged
Greg
El Dorado County, CA
www.meansracing.com

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Filter for MFI
« Reply #10 on: July 26, 2018, 07:46:24 PM »
Quote from: gregm784 on April 27, 2018, 09:30:42 AM
Quote from: noslin on April 26, 2018, 08:00:54 PM
Greg, what micron screen are you using? 

Spud?  Can you answer that? i'm not sure.  Its what he recommended.


Our filter is 63 microns.

Spud
Logged

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions
Pages: [1]   Go Up
« previous next »