« previous next »
Pages: [1]   Go Down

Author Topic: Steering  (Read 4406 times)

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Steering
« on: February 15, 2018, 09:10:37 PM »
Hi Rooman, can you please post a couple pics of how you do steering mounts down the side of the chassis? Do you use Teflon to make the tube slide better? I would like to cut off all my brackets and make it better. Maybe I am being too pikey but would like to get rid of the metal to metal deal. I hope this makes sense. Thank you as for finally after 2.5 years I might be getting my KB block to finally mock everything up. I will post pics as all comes along.
Thanks Greg S.
Logged
If it jams force it, if it breaks it needed replaced anyways

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: Steering
« Reply #1 on: February 20, 2018, 03:53:17 AM »
Greg,
       I just use a simple aluminum slider bracket. I do countersink the hole on either side to reduce the surface area where the link slides but that is about it. I use McKinney's weld tab on the frame--it has a pair of 3/16" holes for 10-32 screws/bolts and the aluminum part is one of my own pieces. Neil and Parks also make a package that uses a single 1/4" bolt to locate the slider.
  On long wheelbase cars (225") I use three slider brackets and 7/8" tube for the link.

Logged
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: Steering
« Reply #2 on: February 20, 2018, 12:27:31 PM »
Thank you.
Logged
If it jams force it, if it breaks it needed replaced anyways

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Steering
« Reply #3 on: February 20, 2018, 01:00:22 PM »
Dragster Supply sells a couple different types of drag ling supports. One made completely out of UHMW plastic and the other out of aluminum with UHMW inserts. Nice and quiet and won't bother your chrome.
Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: Steering
« Reply #4 on: February 20, 2018, 03:20:55 PM »
Neil and Parks also sell some trick coated pieces
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline ducky45356

  • Newbie
  • *
  • Posts: 12
    • View Profile
  • Your Best Time: none
  • Your Engine: 427 chevy blown meth
  • Your Track: muncie
  • Your Vehicle: 175"fed
  • General Location: mid west
Re: Steering
« Reply #5 on: February 25, 2018, 06:32:01 AM »
Here are some I made out of aluminum,with nylon bushings in them.
Logged
Pages: [1]   Go Up
« previous next »