« previous next »
Pages: [1]   Go Down

Author Topic: duration change with lash change  (Read 3482 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
duration change with lash change
« on: February 07, 2018, 07:30:07 AM »
Anyone know of rule of thumb as to how much duration change with lash change.Lets say a 290* @ .050 cam specs .024 lash and you go to .014 lash netting .010 tighter how much duration would you gain? As said rule of thumb is fine since not every cam will be the same.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Roger

  • Full Member
  • ***
  • Posts: 183
    • View Profile
  • Your Vehicle: 125 inch Altered
Re: duration change with lash change
« Reply #1 on: February 07, 2018, 11:43:03 AM »
From Comp Cams:

"The general rule of thumb when adjusting valve lash is that 0.004” of adjustment from the valve lash specified in the cam card equates to a 2° difference in duration when measured at 0.050” lift."
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: duration change with lash change
« Reply #2 on: February 07, 2018, 02:44:17 PM »
Thanks Roger,

 That would mean if I loosed mine up .012 I should loose 6*,which is not problem since I normal run my stuff tight around .010 or so,thats cold. most specs are closer to .024 anyway. Want to drop exhaust side on cam I have to test a theory .
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: duration change with lash change
« Reply #3 on: February 07, 2018, 04:26:17 PM »
Going significantly looser might move the take-up point past the "clearance ramp" on the lobe and make for a harsh impact on the lobe. What constitutes "significantly" I can't say.
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: duration change with lash change
« Reply #4 on: February 07, 2018, 04:36:56 PM »
agree that too loose abuses valve train.As stated since I run lash a lot tighter than spec,loosing up just gets me closer to spec. I have run .004.Two reason tighter has to be better on valve train and I wanted as much duration as I could get at the time due to lousy track and hoping to kill little bottomend power.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: duration change with lash change
« Reply #5 on: February 07, 2018, 05:15:26 PM »
I also run tighter than spec.

I have friends who set their lash, ran the engine up on the dyno @ WOT to simulate race conditions, and quickly shut it down and checked the lash.
It grew by .030". This on an iron block, billet aluminum head. Yikes
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: duration change with lash change
« Reply #6 on: February 07, 2018, 08:08:45 PM »
.030 sounds like other issues. I have run our Top alcohol stuff up to 200 and checked valves.Normal was .008 to .015 growth on aluminum block and billet heads.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot
Pages: [1]   Go Up
« previous next »