Author Topic: Push rod Length  (Read 2630 times)

Offline spitzerscott

  • Full Member
  • ***
  • Posts: 116
    • View Profile
    • Ogg Motorsports
  • Your Best Time: 5.73@118.80
  • Your Engine: 336 Small Block Chevy
  • Your Track: Osceola IN, Top Eliminator runs 1/8 mile
  • Your Vehicle: Spitzer225 RED, Alcohol SBC
  • General Location: Northern Indiana
Push rod Length
« on: March 18, 2018, 09:18:00 AM »
What would be the factors that would make you need to run longer pushrods?  Some are obvious but thought you guys have ran into many, just looking for info.    Thanks

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: Push rod Length
« Reply #1 on: March 18, 2018, 03:58:13 PM »
Many things combine to change the push rod length needed
On any new build you use and adjustable checker push rod--sharpie tip of the valve--roll it over observe pattern on =valve tip--adjust length--re-sharpie--roll her over --check pattern--when the average back yard guy gets a pattern in center of valve tip about wide as a third of stem diameter he should stop measure--order push=rods and never look back
This does not address every situation but covers about 90 % of them for average racer

On a small block Chevy longer valves equals longer push rods in most cases

Most folks use a .100 long valve so they gain installed height for valve springs  usually those engines will use a .100 longer push rod

My advice above does not get into a bunch of math and all of the details but it will work for most guys
« Last Edit: March 19, 2018, 02:24:37 PM by dusterdave173 »
I have always had a fascination with fast cars at the expense of more normal character development

Offline denverflatheader

  • Sr. Member
  • ****
  • Posts: 333
    • View Profile
Re: Push rod Length
« Reply #2 on: March 19, 2018, 12:38:29 PM »
spitzerscott - probably not expected answer to your question, it’s info though.  Switching from a V8 sbc to an inline 6 cylinder needs longer pushrod.  A stock sbc pushrod is 7.900” compared to 10.140” length for a Ford 300 six.  Anything you do to reduce weight for the moving parts in your valvetrain helps your springs be more reliable and allows your engine to rpm easier.  Think about a stock engine’s valvetrain at 5000 rpms and adding even a fraction of weight (e.g. longer pushrod) is a negative.  In this instance the stock V8 sbc has huge advantage over the Ford inline 6 cylinder.  Alan

p.s. Some aftermarket sbc have raised cam location which may require different than stock pushrod length.


Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Push rod Length
« Reply #3 on: March 19, 2018, 04:24:27 PM »
If you have engine where you might change head gaskets for more or less compression start in middle. I made up a set for Hemi with .080 gaskets and when got in lousy air switched to .030 and had cpl pushrods that where just long enough to be problem. Probably not issue for most combos but it happens.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot