« previous next »
Pages: [1]   Go Down

Author Topic: alum small block  (Read 6054 times)

Offline hotrod316

  • Sr. Member
  • ****
  • Posts: 352
    • View Profile
alum small block
« on: October 06, 2017, 06:25:48 AM »
looking for a good used alum gm  small block (410 motor)
moving on up!
thanks
steve m
Logged

Offline alkyal

  • Jr. Member
  • **
  • Posts: 52
    • View Profile
  • Your Track: Quaker City/Dragway 42
  • Your Vehicle: Not a Driver-Nostaliga AA/FD
Re: alum small block
« Reply #1 on: December 31, 2017, 12:25:55 AM »
Did you find a Block? I have a Rodeck that has NOT been Blown Up. It will probably need new Sleeves as its @ .030 over. I will have to check. Has SBC cam bearings. Believe the rear cap is Wet Sump. If interested please reply with a contact number. I am in Ohio. Price will B reasonable as I dont have a real use for it and cant use for our purpose. Thanks Al
Logged

Offline hotrod316

  • Sr. Member
  • ****
  • Posts: 352
    • View Profile
Re: alum small block
« Reply #2 on: December 31, 2017, 09:08:31 AM »
Al, yes we found one but always looking for a back up block  how many nickels?
 
Logged

Offline alkyal

  • Jr. Member
  • **
  • Posts: 52
    • View Profile
  • Your Track: Quaker City/Dragway 42
  • Your Vehicle: Not a Driver-Nostaliga AA/FD
Re: alum small block
« Reply #3 on: December 31, 2017, 10:02:07 PM »
Will check some dimensions and post with asking price by Weds  Al
Logged

Offline alkyal

  • Jr. Member
  • **
  • Posts: 52
    • View Profile
  • Your Track: Quaker City/Dragway 42
  • Your Vehicle: Not a Driver-Nostaliga AA/FD
Re: alum small block
« Reply #4 on: January 07, 2018, 02:01:24 PM »
What I have is an Older Rodeck. Std size Babbit SBC cam Brgs. The Liners are worn .030. Would clean-up @ .035. The rear cap is a dry Sump. Main Caps-Studs and nuts-washers are there also. The block has some damage from a rod-s failure in #1 ad #2. Was run like this. Asking 750.00 plus shipping from Ohio. Block has Rodeck 350 Plus cast into front. Mains are 400 size.
Logged

Offline hotrod316

  • Sr. Member
  • ****
  • Posts: 352
    • View Profile
Re: alum small block
« Reply #5 on: January 08, 2018, 05:35:31 AM »
thanks will check it out
Logged

Offline deepwoods

  • Newbie
  • *
  • Posts: 3
    • View Profile
  • Your Best Time: 6.70 QM
  • Your Engine: ARIAS on 100% 421-496 cu in
  • Your Track: Thompson Drag Raceway
  • Your Vehicle: Neil&Parks FED (A/Fuel)
  • General Location: Midwest
Re: alum small block
« Reply #6 on: January 15, 2018, 06:31:27 AM »
ALKYAL,
Call 440-749-0182
Logged

Offline OldSchoolHP

  • Newbie
  • *
  • Posts: 13
    • View Profile
  • Your Best Time: 8.92/158 - 1320'
  • Your Engine: 434 SBC
  • Your Track: AK Raceway Park
  • Your Vehicle: 125 Altered
  • General Location: Alaska
Re: alum small block
« Reply #7 on: January 11, 2020, 11:25:56 AM »
Quote from: alkyal on January 07, 2018, 02:01:24 PM
What I have is an Older Rodeck. Std size Babbit SBC cam Brgs. The Liners are worn .030. Would clean-up @ .035. The rear cap is a dry Sump. Main Caps-Studs and nuts-washers are there also. The block has some damage from a rod-s failure in #1 ad #2. Was run like this. Asking 750.00 plus shipping from Ohio. Block has Rodeck 350 Plus cast into front. Mains are 400 size.

Did you sell this block?
Logged
Pages: [1]   Go Up
« previous next »