Author Topic: two step with mag  (Read 4059 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
two step with mag
« on: October 01, 2017, 04:57:53 AM »
 I have my car setup with MSD 12.  Any reason 2 step and mag will not work well together? I also have sle on car and figure to have very limited time on 2 step,just enough to hit 6600 before TB releases.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline coupemerc

  • Sr. Member
  • ****
  • Posts: 306
    • View Profile
  • Your Best Time: 3.86@188 (1/8 Mile), 5.97@233 (1/4 Mile)
Re: two step with mag
« Reply #1 on: October 01, 2017, 10:59:52 AM »
It will work fine Chris. I'm using a 2 step and a MSD mag 20 on my deal. No issues

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: two step with mag
« Reply #2 on: October 01, 2017, 01:18:51 PM »
yes we also have a MSD 2 step, and a 20 amp MSD with no problems. I only had one problem with a launch chip that was loose, and I watch the high RPM chip to see if it is off the RPM I want. Some times we have just pulled the high RPM chip out if we think it might be causing it to miss below the what the chip says. Art Chrisman suggested that, and it fixed in our car. Down side is we break a trans or way too much tire smoke and it goes over 10,500RPM. it's over 11k that my engine doesn't like.

Jon
Jon C. Hansen

Hayden Wheels

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: two step with mag
« Reply #3 on: October 01, 2017, 03:30:08 PM »
Thanks guys.I had cpl doubt it and got me be thinking I might be mistaken, should have known better(LOL).
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline George

  • Hero Member
  • *****
  • Posts: 515
    • View Profile
  • Your Vehicle: 1964 Mercury Comet Super Stock/ M automatic
  • General Location: Midwest USA
Re: two step with mag
« Reply #4 on: October 03, 2017, 06:34:08 AM »
Yep, we have been running a MSD 12LT with a 2-step for years. Also an rpm switch for the shifter.

Offline coupemerc

  • Sr. Member
  • ****
  • Posts: 306
    • View Profile
  • Your Best Time: 3.86@188 (1/8 Mile), 5.97@233 (1/4 Mile)
Re: two step with mag
« Reply #5 on: October 03, 2017, 12:03:30 PM »
Scott Parks made me a cool little EMI tight box that I put my 2 step in. Don't know if it helps wiyh the interference from the mag much but the lid of the box keeps a little positive pressure on the MSD chips helping to keep them plugged in. Also, for you guys that like to keep everything secret, the box prevents anyone from seeing what rpm you're launching at.