Author Topic: enderle nozzles onto hilborn 4-port  (Read 3777 times)

Offline 30dodgeboy

  • Newbie
  • *
  • Posts: 31
    • View Profile
  • Your Engine: 1956 354 Chrysler on gas... for now
  • Your Track: Byron Dragway
  • Your Vehicle: 144" FED and a few 67 Coronets
enderle nozzles onto hilborn 4-port
« on: September 18, 2017, 05:27:43 PM »
I have a hilborn 4-port upright injector with the wrong size hilborn nozzles, and a friend of mine has a ton of enderle nozzles. 

What enderle nozzle holders / bodies would work to replace my hilborn nozzles that I have that are too large? 

Would an Enderle 7110 be the right nozzle body to thread into the injector?  Or would that project into the throttle bore too far?

They need the air bleed holes, right?  Can I drill those in myself?

Its a mild 354 with 80A pump on methanol, 4 port with 3" dia butterflies.  No port nozzles (for now).
« Last Edit: September 18, 2017, 05:30:02 PM by 30dodgeboy »
2018 Meltdown Drags - July 20-22 Byron, Illinois

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: enderle nozzles onto hilborn 4-port
« Reply #1 on: September 18, 2017, 09:14:20 PM »
Those fit an 1/8" pipe hole.  Should work.
Greg
El Dorado County, CA
www.meansracing.com

Offline 30dodgeboy

  • Newbie
  • *
  • Posts: 31
    • View Profile
  • Your Engine: 1956 354 Chrysler on gas... for now
  • Your Track: Byron Dragway
  • Your Vehicle: 144" FED and a few 67 Coronets
Re: enderle nozzles onto hilborn 4-port
« Reply #2 on: September 19, 2017, 04:53:51 AM »
or would this style be better?
2018 Meltdown Drags - July 20-22 Byron, Illinois

dreracecar

  • Guest
Re: enderle nozzles onto hilborn 4-port
« Reply #3 on: September 19, 2017, 07:58:33 AM »
Match the tip length as close to the Hilborn nozzles a possable. You want air bleeds, it will help in pulling fuel thru the nozzle long with indicating the direction of the fan spray with the AB hole on top. No need for port nozzles, I ran 6.80's @200 with just the hat nozzles and a 375ci.

  Forgot to mention if this was a 4 or 8 nozzle injector

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: enderle nozzles onto hilborn 4-port
« Reply #4 on: September 19, 2017, 08:58:00 AM »
I'd aim to have them about in the middle of the throttle body if it's a 4 nozzle injector. 
Greg
El Dorado County, CA
www.meansracing.com

Offline JoydayVox

  • Jr. Member
  • **
  • Posts: 95
    • View Profile
    • priligy dapoxetine ebay
  • Your Best Time: Urenulo
  • Your Engine: Ekubyboxe
  • Your Track: Ysehekol
  • Your Vehicle: Ijesu
  • General Location: Eweciq
Re: enderle nozzles onto hilborn 4-port
« Reply #5 on: November 11, 2024, 12:57:36 PM »
<a href=https://fastpriligy.top/>priligy for pe</a> Among eligible patients, 3306 patients were grouped into the Single Single group, 540 patients were grouped into the Single Married group, 686 patients were grouped into the Single DSW group, 17, 623 patients were grouped into the Married Married group, 3043 patients were grouped into the Married DSW group, 7333 patients were grouped into the DSW DSW group, and 558 patients were grouped into the DSW Married group