Author Topic: How much ballast needed on a 60's FED?  (Read 11079 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: How much ballast needed on a 60's FED?
« Reply #15 on: September 27, 2017, 07:59:16 AM »
Interesting thread. I have been trying to decide rather to add some to front for first cpl runs and pull until front raises 3 to 6" for first n 30 or 40'. Right now I have 345 lbs of front end according to scales I borrowed. car with me race ready is 1600 lbs.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: How much ballast needed on a 60's FED?
« Reply #16 on: September 27, 2017, 12:36:58 PM »
Chris I have been finding with my car that a half lbs of air can make a big difference ! Even with the small 12 inch tire it can be too much and I have to lower the air pressure to get some wheel speed or the car will drive to the left or right ! Right now I have no ballast in the car but I also moved every thing I could to the front of the car .

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: How much ballast needed on a 60's FED?
« Reply #17 on: October 04, 2017, 04:22:48 PM »
Hoping I don't need any ballast. Right now battery is in front of axle and tank is right behind axle. I have to 5lb fire bottles behind that. I could move the driver but then it would be RED like every other car at track. I do have mounts and 20 lbs of plates plus a weight tube mount,be prepare.d and hope not to use. If have to add I will get second battery,no work no ride.

Tires are big question. New 3074's M/T's/ 15x14x32.  7.5 lbs starting point.No runs since new tires.Lifes been getting in the way,well family members lives which seem to be my problem. Hopefully get some runs before end of month and good enough for thanksgiving money bash at Farmington.  Will keep pressure deal in mind and work in small jumps.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: How much ballast needed on a 60's FED?
« Reply #18 on: October 06, 2017, 05:56:00 PM »
We ran 14x32 slicks on a fed, prob not as much power as your deal but from my time at the track I would suggest to start at 6psi or lower unless prep stinks. At Bakersfield we could not run much over 5psi but the track prep was excellent every time. 10' wheel stands and broken wheelie bars are not very hard to do even with 40lbs on the nose along with everything else... I am no pro but we have broken a few things in the learning curve.  ;D
If it jams force it, if it breaks it needed replaced anyways