« previous next »
Pages: [1]   Go Down

Author Topic: Front End Caster on a FED  (Read 10583 times)

Offline codysisson

  • Newbie
  • *
  • Posts: 17
  • Cody Sisson, Northfield, MA
    • View Profile
    • Sisson Engineering Corp
  • Your Best Time: 7.90 @ 170 MPH - 1/4 Mile
  • Your Engine: SBC, Injected Alcohol
  • Your Track: New England Dragway
  • Your Vehicle: 2011/2014 Worm Front engine Dragster
Front End Caster on a FED
« on: August 15, 2014, 09:52:36 AM »
I have been trying to find out what a good starting point for caster angle for a 180" FED. SBC, injected alcohol, Projected mid 8's 155 MPH.
I was told that a good rule of thumb was, 1degree of caster per 10 MPH of top end speed and I just wanted to back up that information. I have seen so many front ends at wide varying degrees of caster and cannot seem to find a consistent consensus.

I plan to dyno the engine next week, the roller is all done so I should be running mid to late September.
Logged

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Front End Caster on a FED
« Reply #1 on: August 15, 2014, 11:22:36 AM »
Your bound to get a bunch of different replies, but I can tell you that I run 12-14 degrees in every car I build with Anglia style spindles. No matter how fast they think they're going to go, thats what I put in them. There's usually enough adjustment to get a few more degrees to compensate for taller tires or tires that grow more on a run, but from the slowest cars I've built (100 mph) to the fastest (220 mph) I start them all the same. If NED is your home track and you're into nostalgia racing you've probably seen some of my cars run.
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Front End Caster on a FED
« Reply #2 on: August 15, 2014, 03:39:52 PM »
Quote from: fuel749 on August 15, 2014, 11:22:36 AM
Your bound to get a bunch of different replies, but I can tell you that I run 12-14 degrees in every car I build with Anglia style spindles. No matter how fast they think they're going to go, thats what I put in them. There's usually enough adjustment to get a few more degrees to compensate for taller tires or tires that grow more on a run, but from the slowest cars I've built (100 mph) to the fastest (220 mph) I start them all the same. If NED is your home track and you're into nostalgia racing you've probably seen some of my cars run.
  Did you build Sam Dagir's car ?
Logged

Offline H.G. Wells

  • Full Member
  • ***
  • Posts: 116
    • View Profile
  • Your Engine: Mild 383 SBC or 498 blown BBC
  • Your Track: Currently San Antonio, past Amarillo, Ardmore OK, Noble OK
  • Your Vehicle: late 60's FED of unknown origin
Re: Front End Caster on a FED
« Reply #3 on: August 15, 2014, 07:00:16 PM »
I run 13 degrees. 
Logged
Racecar spelled backwards is racecaR

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Front End Caster on a FED
« Reply #4 on: August 16, 2014, 05:42:02 AM »

[/quote]  Did you build Sam Dagir's car ?
[/quote]
 
Yes I did, in 2003.
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Front End Caster on a FED
« Reply #5 on: August 16, 2014, 11:40:16 AM »
Quote from: fuel749 on August 16, 2014, 05:42:02 AM

  Did you build Sam Dagir's car ?
[/quote]
 
Yes I did, in 2003.
[/quote]   Sam's car is really nice !
Logged

Offline rooman

  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: Front End Caster on a FED
« Reply #6 on: August 17, 2014, 09:10:11 AM »
I build mine at 20 degrees, although Brendan Murry's is 30--his preference.

Roo
Logged
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline ss4

  • Jr. Member
  • **
  • Posts: 98
    • View Profile
  • Your Best Time: 5.42 @ 128 - 1/8th
  • Your Track: Northern Michigan Dragway
  • Your Vehicle: Worm Inc. 180 inch Front Engine Dragster
Re: Front End Caster on a FED
« Reply #7 on: August 18, 2014, 01:50:13 PM »
I was told that same rule of thumb and it is working for me.  just ran 158 with 15deg.  I am pretty sure I could have run hands off the wheel the full lengthen.
Logged
if you need to Hate target Laziness

Offline codysisson

  • Newbie
  • *
  • Posts: 17
  • Cody Sisson, Northfield, MA
    • View Profile
    • Sisson Engineering Corp
  • Your Best Time: 7.90 @ 170 MPH - 1/4 Mile
  • Your Engine: SBC, Injected Alcohol
  • Your Track: New England Dragway
  • Your Vehicle: 2011/2014 Worm Front engine Dragster
Re: Front End Caster on a FED
« Reply #8 on: August 19, 2014, 03:03:48 PM »
Thank you all for your input. I have the axle set up now for 15 degrees and we will see how that works on the shake-down runs. I am sure it will be just fine!
Logged

Offline JoydayVox

  • Full Member
  • ***
  • Posts: 139
    • View Profile
    • dapoxetine for premature ejaculation
  • Your Best Time: Urenulo
  • Your Engine: Ekubyboxe
  • Your Track: Ysehekol
  • Your Vehicle: Ijesu
  • General Location: Eweciq
Re: Front End Caster on a FED
« Reply #9 on: November 18, 2024, 07:44:02 PM »
DCC Dextran coated charcoal, ERE estrogen response elements, HC hydroxycholesterol, LTED, long term estrogen deprivation, wt wild type buy priligy in usa is a Damon Runyon Merck Clinical Investigator
Logged
Pages: [1]   Go Up
« previous next »