Author Topic: Champ Dragster Oil Pans  (Read 5837 times)

Offline arush

  • Jr. Member
  • **
  • Posts: 59
    • View Profile
  • Your Engine: Blown-Alcohol-Injected 427 BBC
  • Your Track: Thompson Raceway Park
  • Your Vehicle: King Chassis 160" FED
  • General Location: Pa.
Champ Dragster Oil Pans
« on: August 26, 2016, 06:58:09 PM »
Anyone out there ever run a Champ Oil Pan? They are made in America and have been in business for over thirty years.

Offline MikenMpls

  • Jr. Member
  • **
  • Posts: 80
    • View Profile
  • Your Engine: 408 dart little m block and Iron Eagle heads
  • Your Track: Cameron, MO
  • Your Vehicle: 205" FED
Re: Champ Dragster Oil Pans
« Reply #1 on: August 26, 2016, 08:49:39 PM »
Run an aluminum KEVKO pan from Fairmont, MN. Small shop building nice pans at a great price!

dreracecar

  • Guest
Re: Champ Dragster Oil Pans
« Reply #2 on: August 27, 2016, 09:15:35 AM »
What does "made in America" have to do with it???? sounds like you are promoting them instead of asking about if anyone is running them and how they work.
Not enough volume to have race pans made overseas. I did see some alu pans for 426 fuel engines made overseas, design was nice (copied) and the welding was good and clean, only problem was that they were warped so bad that they would not bolt up.
 As a fuel racer, I would welcome a cheaper pan, Bad enough to throw rods out , but now will have to spend another $750 for a pan

Offline arush

  • Jr. Member
  • **
  • Posts: 59
    • View Profile
  • Your Engine: Blown-Alcohol-Injected 427 BBC
  • Your Track: Thompson Raceway Park
  • Your Vehicle: King Chassis 160" FED
  • General Location: Pa.
Re: Champ Dragster Oil Pans
« Reply #3 on: August 27, 2016, 07:00:57 PM »
Thanks MikenMpls for the lead.
Bruce I am not promoting them. My son just found them on the internet. I was just sharing the information from their site. I try to buy American whenever I can. With them being in business for 30 years (if its true) kind of lets me know that it is not some guy working in his dirt floor garage with his brother in law Vinny making oil pans. I to have experienced some (copied) pans and could never get them to seal right. I never heard of them before and was wondering if anyone had and if they were a quality product. That's it. No hidden agenda here.

Offline PSweeney

  • Full Member
  • ***
  • Posts: 231
    • View Profile
  • Your Track: Santa Pod
  • Your Vehicle: 138in SBC slingshot
Re: Champ Dragster Oil Pans
« Reply #4 on: September 07, 2016, 04:26:43 AM »
I have one, seemed reasonable quality but I had to cut it around for ground clearance.

Offline arush

  • Jr. Member
  • **
  • Posts: 59
    • View Profile
  • Your Engine: Blown-Alcohol-Injected 427 BBC
  • Your Track: Thompson Raceway Park
  • Your Vehicle: King Chassis 160" FED
  • General Location: Pa.
Re: Champ Dragster Oil Pans
« Reply #5 on: September 07, 2016, 08:32:00 AM »
Appreciate your feed back PSweeney. Decided to use a pan that I already have and I am also in the process of cutting it for ground clearance.

Offline KeninIowa

  • Newbie
  • *
  • Posts: 2
    • View Profile
  • Your Track: Earlville
  • Your Vehicle: 68 Chevelle
Re: Champ Dragster Oil Pans
« Reply #6 on: October 03, 2016, 04:45:09 PM »
No experience with their drag race stuff but I know they make some of the nicest wet-sump circle track pans available.  I've had a few.

Offline Totally T

  • Full Member
  • ***
  • Posts: 141
    • View Profile
    • NDRL
Re: Champ Dragster Oil Pans
« Reply #7 on: October 03, 2016, 05:55:06 PM »
I ran one for years and had no issues...also had the oil pump that they recommend with it.
Troy Wilson
Nostalgia Drag Racing League