« previous next »
Pages: [1]   Go Down

Author Topic: wires etc from driver to front  (Read 7794 times)

Offline probird

  • Jr. Member
  • **
  • Posts: 75
    • View Profile
  • Your Track: alberta
wires etc from driver to front
« on: January 31, 2016, 08:32:45 PM »
Hello Fedders!
Progress is coming along good. I'm waiting for my welder to get back from up north. In the mean time I'm trying to figure out routing of the wiring and cables. When I received my car, the wiring and cables were run beside the midplate. can I do this again?
One main power for the cab compartment, power shutoff cable, coil wires to the dist., throttle cable and a few small wires for relays in front.
Thanks
Barry
Logged

Offline rooman

  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: wires etc from driver to front
« Reply #1 on: February 01, 2016, 04:58:33 AM »
Baz,
      I is a little difficult to do in a retrofit situation but I put sleeves in the motor uprights for cables, electrical. fire bottle lines.

Roo
Logged
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: wires etc from driver to front
« Reply #2 on: February 01, 2016, 05:14:22 AM »
I did mine as Rooman stated.I did not do enough and had to add more.Step drill and 90* drill are your friends here.Problem is not so much welding them in as drilling them,I used 3/4" tubing to allow room for multiple wires in one and for cables.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline probird

  • Jr. Member
  • **
  • Posts: 75
    • View Profile
  • Your Track: alberta
Re: wires etc from driver to front
« Reply #3 on: February 01, 2016, 06:33:02 AM »
Ok. Looks like I'll go pick up a step drill today.
Thanks guys!
Logged

Offline grapro

  • Jr. Member
  • **
  • Posts: 71
    • View Profile
  • Your Track: edmonton
  • Your Vehicle: 184" FED
Re: wires etc from driver to front
« Reply #4 on: February 01, 2016, 08:29:39 AM »
Barry
I have lots of step drills
Logged

Offline rooman

  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: wires etc from driver to front
« Reply #5 on: February 01, 2016, 09:40:16 AM »
Actually a set of Blair Rotabroach cutters works best for me if I am forced to do it in place. That does restrict you to 3/4" with the basic and most readily available kit.

Roo
Logged
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 570
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: wires etc from driver to front
« Reply #6 on: February 01, 2016, 10:09:56 AM »
Could you guys share some pictures?

This is an area begging for improvement in my FED.
Logged

Offline George

  • Hero Member
  • *****
  • Posts: 515
    • View Profile
  • Your Vehicle: 1964 Mercury Comet Super Stock/ M automatic
  • General Location: Midwest USA
Re: wires etc from driver to front
« Reply #7 on: February 01, 2016, 11:18:26 AM »
Logged

Offline probird

  • Jr. Member
  • **
  • Posts: 75
    • View Profile
  • Your Track: alberta
Re: wires etc from driver to front
« Reply #8 on: February 01, 2016, 11:23:34 AM »
Canadian tire had a set on sale. will put 2 3/4 inch ones in each side.
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: wires etc from driver to front
« Reply #9 on: February 01, 2016, 11:24:22 AM »
Here is a picture of mine
Logged

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 570
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: wires etc from driver to front
« Reply #10 on: February 01, 2016, 03:05:42 PM »
Thanks for the picture Bill. That's exactly what I have in mind with mine.

PS.: You have a very well setup car!
Logged

Offline Van

  • Full Member
  • ***
  • Posts: 116
    • View Profile
  • Your Best Time: 7.11 @ 189 with this car
  • Your Engine: Lincoln blown alky 534
  • Your Track: Bakersfield Ca.
  • Your Vehicle: Dragster
  • General Location: west coast
Re: wires etc from driver to front
« Reply #11 on: February 01, 2016, 06:20:31 PM »
 I recently added one on each side of my Dragster, but I used Airframe oval tubing (strut tube) I can stack 3 cables easily on each side. This looked to be an easy way to get the job done with less drilling & welding and gets everything through in one place down low. I drilled the starter hole and used a die grinder to shape the hole to the tubing.
Logged
Pages: [1]   Go Up
« previous next »