« previous next »
Pages: [1]   Go Down

Author Topic: Setting Hi-speed bypass  (Read 5668 times)

Offline msundstrom

  • Full Member
  • ***
  • Posts: 119
    • View Profile
  • Your Best Time: 7.45 @ 182 in 1/4
  • Your Engine: NA Injected 505 BBC on 45%
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: FED
  • General Location: Washington Coast
Setting Hi-speed bypass
« on: October 19, 2015, 03:47:33 PM »
Hi Spud,
If I need to set my Hi-speed in the 120's psi but my air pressure source is maxed at 110 psi, what is my alternative source?
Thanks
Mark S
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 744
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Setting Hi-speed bypass
« Reply #1 on: October 19, 2015, 07:27:55 PM »
CO2 bottle is what I use at the track
Logged

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Setting Hi-speed bypass
« Reply #2 on: October 20, 2015, 09:15:47 AM »

 Yup, CO2 or nitrogen works great. If you don't have a bottle of some kind of gas around to use, shim it one shim at a time and write down the pressure increase for each until you get to your max available air pressure. Then figure how much gain you're getting per shim (it won't be perfectly linear, but close). Then project how many shims it'll take to get where you need to be. Extrapolation :) You'll be within a few pounds.

 Spud
Logged

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline msundstrom

  • Full Member
  • ***
  • Posts: 119
    • View Profile
  • Your Best Time: 7.45 @ 182 in 1/4
  • Your Engine: NA Injected 505 BBC on 45%
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: FED
  • General Location: Washington Coast
Re: Setting Hi-speed bypass
« Reply #3 on: October 21, 2015, 08:42:31 AM »
 Thanks a lot guys. 
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 744
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Setting Hi-speed bypass
« Reply #4 on: October 21, 2015, 12:20:45 PM »
Oh yes Nitrogen would be a better option I just have CO2 onboard for my shifter
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Setting Hi-speed bypass
« Reply #5 on: October 21, 2015, 01:46:37 PM »
While we are on the subject what have some of you guy's picked up with a high speed ? I have not tried one yet
Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: Setting Hi-speed bypass
« Reply #6 on: October 21, 2015, 02:36:57 PM »
Good question--I have a 355 CI sbc run mostly 1/8th some 1/4    2 3/16ths  Hilborn--will a hi speed gain me some mph and et and is it worth the trouble
Logged
I have always had a fascination with fast cars at the expense of more normal character development
Pages: [1]   Go Up
« previous next »