« previous next »
Pages: [1] 2   Go Down

Author Topic: Help need a 6.40 for license  (Read 12926 times)

Offline imcamod17

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Track: Muncie Dragway
  • Your Vehicle: 200" Hal Canode FED
Help need a 6.40 for license
« on: August 01, 2015, 03:01:47 PM »
I was wandering how to drop a couple of tenths on an eighth mile pass. I need a 6.40 or quicker in the 1/8th for my last 2 license runs and I can only muster a 6.52. I am going to upgrade this winter but anyone know any tricks to gain a couple of tenths.  I ran a 1.42 60',  I ran a 10.27 @ 127mph in the quarter mile.   I thought about pulling  out the 16lbs of fire  system and going on a diet.   Just thought I wolud ask. Proly should wait till I have more power next year. It  is an old worn out 327, dart iron eagle heads,  850 holley,  with about 700 laps in my asphalt, modified on it. 
Logged

dreracecar

  • Guest
Re: Help need a 6.40 for license
« Reply #1 on: August 01, 2015, 03:17:58 PM »
Stage as shallow as you can that way you get moving and run at the beams before they start timing, a little more air pressure so that the tires dont wind up as much
Logged

Offline imcamod17

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Track: Muncie Dragway
  • Your Vehicle: 200" Hal Canode FED
Re: Help need a 6.40 for license
« Reply #2 on: August 01, 2015, 03:20:05 PM »
Had 8 pounds in the rear tires. Hoosier 31" by 12.5.
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Help need a 6.40 for license
« Reply #3 on: August 01, 2015, 04:54:45 PM »
If you have no nose piece you can add 30" from axle centerline and break beak sooner.Not a lot but its something gained.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Help need a 6.40 for license
« Reply #4 on: August 01, 2015, 05:00:06 PM »
know anyone with aluminum heads you can borrow? hundred pounds would be roughly .10 in quarter probably .06 in 1/8. alky carb if can borrow should be good for .05 to .10,but would need whole system with pump.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Help need a 6.40 for license
« Reply #5 on: August 01, 2015, 05:31:51 PM »
Smaller rear tire 11" width is plenty for the et your shooting for maybe even a 10"
Logged

Offline imcamod17

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Track: Muncie Dragway
  • Your Vehicle: 200" Hal Canode FED
Re: Help need a 6.40 for license
« Reply #6 on: August 02, 2015, 06:13:37 AM »
Copy, thanks for the input. I have another motor that needs gone through, that ran a 6.1 10 years ago. I was just fishing for ideas, thank you.
Logged

Offline George

  • Hero Member
  • *****
  • Posts: 515
    • View Profile
  • Your Vehicle: 1964 Mercury Comet Super Stock/ M automatic
  • General Location: Midwest USA
Re: Help need a 6.40 for license
« Reply #7 on: August 02, 2015, 06:41:20 AM »
Agree with Paul . Way too much tire for your power level.
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Help need a 6.40 for license
« Reply #8 on: August 02, 2015, 06:55:56 AM »
Not knowing your combination it is kind of hard to come up with idea's . A couple of things would be a little more timing like 2 degree's or advance the cam a little if you have the room . A looser converter or lower rear gear . Hope this helps . Bill
Logged

Offline BK

  • Sr. Member
  • ****
  • Posts: 310
    • View Profile
  • Your Best Time: 8.45 / 5.30
  • Your Track: Empire Dagway
  • Your Vehicle: Late 70's FED
Re: Help need a 6.40 for license
« Reply #9 on: August 02, 2015, 08:02:14 AM »
Run the front tire pressure as low as you dare. Will give you more roll out. Air up slicks till they spin a little. Yes more than 8.
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Help need a 6.40 for license
« Reply #10 on: August 02, 2015, 03:59:04 PM »
Easiest thing a little 150or 200 shot.Should get you more than enough and for just cpl shots should be plenty safe. I have run 250 shot on bone stock street stuff not a problem.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline hotrod316

  • Sr. Member
  • ****
  • Posts: 352
    • View Profile
Re: Help need a 6.40 for license
« Reply #11 on: August 02, 2015, 06:11:53 PM »
25-30% pop
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Help need a 6.40 for license
« Reply #12 on: August 04, 2015, 02:06:41 PM »
Quote from: wideopen231 on August 02, 2015, 03:59:04 PM
Easiest thing a little 150or 200 shot.Should get you more than enough and for just cpl shots should be plenty safe. I have run 250 shot on bone stock street stuff not a problem.
   we have a winner !!!
Logged

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 570
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: Help need a 6.40 for license
« Reply #13 on: August 04, 2015, 04:39:43 PM »
Quote from: hotrod316 on August 02, 2015, 06:11:53 PM
25-30% pop

This my pick Bill, just pour it and run. Have you ever tipped the can instead spraying?
Logged

Offline George

  • Hero Member
  • *****
  • Posts: 515
    • View Profile
  • Your Vehicle: 1964 Mercury Comet Super Stock/ M automatic
  • General Location: Midwest USA
Re: Help need a 6.40 for license
« Reply #14 on: August 04, 2015, 07:18:18 PM »
Hey Ricardo, Have you been running your car ? Some of our NQS cars have run Bean Blossom. I believe Gayle Jenkins has the FED track record? Do you run any nitro? Are you a 4.99 or quicker car? We have a nice program and are always looking for some new blood. George


Guess not. Lol
« Last Edit: August 08, 2015, 02:09:30 AM by George »
Logged
Pages: [1] 2   Go Up
« previous next »