Author Topic: Front Spindles  (Read 5521 times)

Offline Racing6

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Track: El Paso Motorplex
  • Your Vehicle: Old Slingshot Dragster
Front Spindles
« on: February 24, 2015, 06:35:57 AM »
My car has home made spindles and I need front wheels. I have found some spindles but don't know how to ID them I can stay with original or use new, just don't what I have   

dreracecar

  • Guest
Re: Front Spindles
« Reply #1 on: February 24, 2015, 07:58:57 AM »
Hold them up to the computer screen so that someone might be able to ID them.

Seriously---If you want something ID'd   YOU HAVE TO POST PICTURES!!!!!

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: Front Spindles
« Reply #2 on: February 24, 2015, 09:33:30 AM »
Also measure the spindle length, &  inner [ closest to the king pin] bearing area OD and outer [ cotter-pin/ nut] bearing OD, and post them or Email me jchansen60@gmail.com,  I no doubt will have wheels for you, or can make something.

Jon Hansen, Hayden Wheels, 800-624-3803
Jon C. Hansen

Hayden Wheels

Offline Racing6

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Track: El Paso Motorplex
  • Your Vehicle: Old Slingshot Dragster
Re: Front Spindles
« Reply #3 on: February 24, 2015, 04:04:06 PM »
Sorry about Pictures, I was asking how to ID them  But good point will get instruction from my grandkid tonight on how to up load a picture and post it tomorrow. Jon shaft length is 3.46 inch, Large bearing is .99 inch,small bearing .626 These are from spindle I found. Will get measurements of original tonight Thanks will e-mail you to get prices of wheels

dreracecar

  • Guest
Re: Front Spindles
« Reply #4 on: February 24, 2015, 04:17:56 PM »
Inner should be 25mm and the outer .625 for it to be considered an Anglia type. Very common, and still quite prevalent today.  kingpin dia shoud be close to 11/16

Offline Racing6

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Track: El Paso Motorplex
  • Your Vehicle: Old Slingshot Dragster
Re: Front Spindles
« Reply #5 on: February 25, 2015, 05:42:04 AM »
Thank You those are the sizes

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: Front Spindles
« Reply #6 on: February 25, 2015, 12:06:23 PM »
Yes, Bruce is right you have Anglia type spindles,
let me know if you want wheels, if cost is an issue, call me I have some trade-ins/ close-outs for sale.

Jon, Haydenent.com, 805-444-4489
Jon C. Hansen

Hayden Wheels