« previous next »
Pages: [1] 2   Go Down

Author Topic: taking out radiator - cooling options  (Read 23961 times)

Offline FEDNV

  • Jr. Member
  • **
  • Posts: 99
    • View Profile
  • Your Best Time: 7.65 @ 175mph - 1/4
  • Your Engine: 560 BBC
  • Your Track: Sacramento
  • Your Vehicle: 185" FED
taking out radiator - cooling options
« on: January 26, 2015, 07:54:57 AM »
Since I am redoing everything on my car and running alcohol I have decided to not put my radiator back in the car.  I was planning on filling the block with water but was wondering if just using block off plates for the water pump is fine or if I should use something like this http://www.jegs.com/i/Dedenbear/302/WH2/10002/-1?parentProductId=1418208 and a remote water pump to just circulate water? 

While running alcohol I have never run my water pump until after a pass as it is fine during the burnout and staging and reaches about 160-180 and about 200 after the pass.  I also warm the car up and heat up the oil in the pits before staging.

I also got a new oil pan that has a pan heater.

thanks
Scott
Logged

dreracecar

  • Guest
Re: taking out radiator - cooling options
« Reply #1 on: January 26, 2015, 08:23:45 AM »
Are you running a blower???
Logged

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: taking out radiator - cooling options
« Reply #2 on: January 26, 2015, 09:09:38 AM »
I run a pump and radiator in the dragster.

If I had to do over I would mount the radiator pump and fan in the trailer in the pits and run quick disconnect hoses from the trailer to the engine when return to the pits to cool the engine down for the next round.

I have seen that setup work and it works well.
Logged
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline H.G. Wells

  • Full Member
  • ***
  • Posts: 116
    • View Profile
  • Your Engine: Mild 383 SBC or 498 blown BBC
  • Your Track: Currently San Antonio, past Amarillo, Ardmore OK, Noble OK
  • Your Vehicle: late 60's FED of unknown origin
Re: taking out radiator - cooling options
« Reply #3 on: January 26, 2015, 09:25:08 AM »
If you are towed to the line and towed back to the pits after the run you should be fine dry. Lots of cars run water in the block and heads with no pump and it steams out as a direct loss system, this will reduce hot spots but I never liked it. Glenns thought on the trailer system would be great if you are making rounds.

Logged
Racecar spelled backwards is racecaR

Offline FEDNV

  • Jr. Member
  • **
  • Posts: 99
    • View Profile
  • Your Best Time: 7.65 @ 175mph - 1/4
  • Your Engine: 560 BBC
  • Your Track: Sacramento
  • Your Vehicle: 185" FED
Re: taking out radiator - cooling options
« Reply #4 on: January 26, 2015, 09:39:47 AM »
I do not run a blower just N/A.

I was told by the guy that does my heads not to run it dry as it will cause hot spots.

I was still going to run an overflow tank off of the normal spot on neck filler if that makes any difference.

I am towed to the line and towed back to the pits.  I run NE1 so I normally have some time between rounds for cool down.

I have an open trailer so no way I could do that radiator deal (hard enough to carry all my crap now) but I guess I could always drain it and refill with cool fresh water if needed between rounds.
Logged

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 570
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: taking out radiator - cooling options
« Reply #5 on: January 26, 2015, 10:26:32 AM »
Quote from: FEDNV on January 26, 2015, 09:39:47 AM
...
 but I guess I could always drain it and refill with cool fresh water if needed between rounds.
...
I wouldn't do that, as head gaskets and such may not like the thermal shock. In other hand, this may not be too different from the stationary radiator on a trailer...
Logged

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: taking out radiator - cooling options
« Reply #6 on: January 26, 2015, 11:25:31 AM »
With the stationary radiator in the trailer there would be water in the block.

With the setup that I saw he was using air hoses as his quick connect/disconnect (small diameter).

With the small diameter hoses and the long length of hoses the thermo shock would be quite mild.

Logged
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

dreracecar

  • Guest
Re: taking out radiator - cooling options
« Reply #7 on: January 26, 2015, 11:26:12 AM »
Iron or alu heads???   I run a waterpump (River Rat---fuel pump extention--cam driven) on a blown alky deal (heads only) and then I know people that dont and they run fine dry. Heard the Hot Spot story before, never paid attention to it when running injected and was never a problem. There is a NE-1 page on FB , talk to the racers on there
Logged

Offline husker-rat

  • Newbie
  • *
  • Posts: 7
    • View Profile
  • Your Track: Mid-America Motorplex
  • Your Vehicle: 65 Nova and working on a 23T altered
Re: taking out radiator - cooling options
« Reply #8 on: January 26, 2015, 12:31:37 PM »
I would not change it. If it was working before why change it? Too many variables when doing such a change. You will be spending more time changing things than what you will gain. I tried this on a  D/ED in the 70's and ended up putting it all back on. Just my 2 cents worth.
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: taking out radiator - cooling options
« Reply #9 on: January 26, 2015, 12:34:11 PM »
Quote from: dreracecar on January 26, 2015, 11:26:12 AM
Iron or alu heads???   I run a waterpump (River Rat---fuel pump extention--cam driven) on a blown alky deal (heads only) and then I know people that dont and they run fine dry. Heard the Hot Spot story before, never paid attention to it when running injected and was never a problem. There is a NE-1 page on FB , talk to the racers on there


I have been running the river rat pump for 10+ years on my blown Alky sbc
Logged

Offline tony1966

  • Newbie
  • *
  • Posts: 34
    • View Profile
  • Your Best Time: 7.62 1/4 mile
  • Your Track: Great Lakes Dragaway
  • Your Vehicle: 2008 FED
Re: taking out radiator - cooling options
« Reply #10 on: January 26, 2015, 03:13:21 PM »
I was planning a similar thing this year with my junk. I was planning on eliminating the radiator an looping the water pump lines so i can keep the w/p running and not kill the temp but keep water flowing. We'll see...

Tony
Logged

Offline FEDNV

  • Jr. Member
  • **
  • Posts: 99
    • View Profile
  • Your Best Time: 7.65 @ 175mph - 1/4
  • Your Engine: 560 BBC
  • Your Track: Sacramento
  • Your Vehicle: 185" FED
Re: taking out radiator - cooling options
« Reply #11 on: January 26, 2015, 03:54:24 PM »
I run aluminum heads and I have already had an exhaust port crack and fixed so I want to put water in it.

Tony that is a great idea for just looping the line on the water pump.  I might give that a try as I already have all the parts to do that.
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: taking out radiator - cooling options
« Reply #12 on: January 26, 2015, 07:01:46 PM »
Here is the River Rat pump on my car


Sent from my iPhone using Tapatalk
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: taking out radiator - cooling options
« Reply #13 on: January 26, 2015, 07:12:10 PM »
You can see my reservoir tank mounted to the cylinder head with water running through the cylinder heads and tank only I run solid copper head gaskets with no water ports


Sent from my iPhone using Tapatalk
Logged

dreracecar

  • Guest
Re: taking out radiator - cooling options
« Reply #14 on: January 27, 2015, 08:17:13 AM »
Same system I have been running for 20 years now
Logged
Pages: [1] 2   Go Up
« previous next »