« previous next »
Pages: [1]   Go Down

Author Topic: SET UP ON REAR GEARS  (Read 8478 times)

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
SET UP ON REAR GEARS
« on: October 21, 2014, 12:36:57 PM »
Well we had a great time at CHRR for sure until spool let loose of all left axle splines. So my question is on setting up gears. Does everyone set gears up just like any other set of gears? Or do you shoot for a tighter backlash with a good pattern or just perfect pattern? Thanks for input as usual.
Logged
If it jams force it, if it breaks it needed replaced anyways

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: SET UP ON REAR GEARS
« Reply #1 on: October 21, 2014, 01:12:44 PM »
Quote from: hemidakota on October 21, 2014, 12:36:57 PM
Well we had a great time at CHRR for sure until spool let loose of all left axle splines. So my question is on setting up gears. Does everyone set gears up just like any other set of gears? Or do you shoot for a tighter backlash with a good pattern or just perfect pattern? Thanks for input as usual.

Try posting this here, Dan Dishon's Transmission Den
http://www.frontenginedragsters.org/forum/index.php?board=36.0
Logged
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: SET UP ON REAR GEARS
« Reply #2 on: October 21, 2014, 02:27:33 PM »
Quote from: hemidakota on October 21, 2014, 12:36:57 PM
Well we had a great time at CHRR for sure until spool let loose of all left axle splines. So my question is on setting up gears. Does everyone set gears up just like any other set of gears? Or do you shoot for a tighter backlash with a good pattern or just perfect pattern? Thanks for input as usual.
    Was it an alluminum spool ?
Logged

dreracecar

  • Guest
Re: SET UP ON REAR GEARS
« Reply #3 on: October 21, 2014, 04:05:13 PM »
Been running the same alu spool and 31 spline axles for since '91, last time I checked it was '95, Blown alc 7-0Pro
Logged

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: SET UP ON REAR GEARS
« Reply #4 on: October 21, 2014, 07:17:51 PM »
Yes it was a 31 spline axle and alum spool
Logged
If it jams force it, if it breaks it needed replaced anyways

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: SET UP ON REAR GEARS
« Reply #5 on: October 22, 2014, 12:11:22 PM »
The 31 spline is kind of small . As for the gears I tend to set them on the loose side . I try to set them around .010 but if they end up at .012 thats ok .  I use a tool to set my pinion depth but some times you may have to move it a couple of thou either way to get a good pattern . Just don't rush . Bill
Logged

Offline FEDNV

  • Jr. Member
  • **
  • Posts: 99
    • View Profile
  • Your Best Time: 7.65 @ 175mph - 1/4
  • Your Engine: 560 BBC
  • Your Track: Sacramento
  • Your Vehicle: 185" FED
Re: SET UP ON REAR GEARS
« Reply #6 on: October 22, 2014, 02:41:01 PM »
So find out that the case is cracked so I will be upgrading.  Going with a 3.25 bearing case so we can go 35 or 40 spline.  What do you guys think about an aluminum case for the FED?  Found some info online saying the aluminum is for a lighter (under 2000 lbs) car.  Is it worth the weight savings vs the strength?
Also, something else we found when taking it apart is the axle splines only went into the spool about 1" on both sides.  Is this normal?  Didn't seem like a lot of contact.
Logged

dreracecar

  • Guest
Re: SET UP ON REAR GEARS
« Reply #7 on: October 22, 2014, 05:17:41 PM »
40 spline is a waste, 35 pretty much standard across the board. Aluminum is strong enough to get the job done and then  some. If you need weight back there ,go with the iron, If not and the price is OK then the alu. Spline ingagment should be equal to the dia of the axle plus 25%. Be careful on mixing supliers, MW offers a propiatary spline along with standard spline.
 If your housing has Ford bearing ends and is 27-3/8" bearing flange to bearing flange, I have a really nice pair of standard 35 spline MW liteweight  axles w/studs and bearings
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: SET UP ON REAR GEARS
« Reply #8 on: October 23, 2014, 11:52:05 AM »
If you have to buy a case I wold go with the aluminum one . The Mark Williams through bolt case is really nice and uses 7/16 studs for the pinion support . As Bruce said the 35 spline is just fine for what you are doing .
Logged
Pages: [1]   Go Up
« previous next »