Author Topic: Fitting Leak  (Read 10916 times)

Offline Oldschool

  • Full Member
  • ***
  • Posts: 122
    • View Profile
  • Your Best Time: 8.42 in a BB Chevy Altered 9.28 in my Vega
  • Your Engine: 434 Scott Shafiroff Racing Engine
  • Your Track: US 36 , Mo Kan and Heartland Park Topeka
  • Your Vehicle: 173" Front Engine Dragster
Fitting Leak
« on: September 27, 2014, 03:20:52 PM »
I have a couple fitting on my hose to my radiator.  The upper fitting are fine,but lower leak. I have tried everything,but nothing works. They are a Jeg's house brand # 16 fittings. Here are a couple pictures and shows were they are leaking. They are leaking between the nut and were the fitting bends into the nut. I have not run in to this on major brands,but thought I would try these ( cheaper ). Any opinion ?
It is not the years in your life
But the life in your years

dreracecar

  • Guest
Re: Fitting Leak
« Reply #1 on: September 27, 2014, 06:32:29 PM »
Expensive engine --  cheap fittings , not a good combo, and now you have to buy new ones, no money savings there.

  If it was just at the nut and fitting you can buy AN sealing washers, I carry a selection in the tool box just in case. Could be just Chinese crap for their cheapline stuff, call Jegs and complain as they have a good return policy.

Offline Oldschool

  • Full Member
  • ***
  • Posts: 122
    • View Profile
  • Your Best Time: 8.42 in a BB Chevy Altered 9.28 in my Vega
  • Your Engine: 434 Scott Shafiroff Racing Engine
  • Your Track: US 36 , Mo Kan and Heartland Park Topeka
  • Your Vehicle: 173" Front Engine Dragster
Re: Fitting Leak
« Reply #2 on: September 27, 2014, 09:50:33 PM »
I know,but these are house brand from Jeg's. I just thought they would be ok, but I guess not. Paid $25 each and the good stuff would have cost $50 each. I called Jeg's and they said to send back and they would replace.I always get the best for my car and if I can not afford it,I wait until I can. Just this time I did not.
It is not the years in your life
But the life in your years

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: Fitting Leak
« Reply #3 on: September 28, 2014, 08:38:45 PM »
I like these

http://www.xrp.com/

You can get them from Midwest Proformance hardware

http://mphindy.com/

Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Fitting Leak
« Reply #4 on: September 29, 2014, 05:29:50 AM »
Now you know why you normally wait to buy best. 

Another reason I don't have cooling . One richening valve and close off part of bypass and temp guage will drop.less things to leak and less weight.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: Fitting Leak
« Reply #5 on: September 29, 2014, 11:17:57 AM »
Now you know why you normally wait to buy best. 

Another reason I don't have cooling . One richening valve and close off part of bypass and temp guage will drop.less things to leak and less weight.
         Chris when you do that wouldn't it tend to milk the oil ?

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Fitting Leak
« Reply #6 on: September 29, 2014, 06:33:27 PM »
don't have to get stupid with it. If system is set to run with correct mixture.You can split return into two seperate jets that total same flow as the one you normally run.Have a normally open valve in line of the smallest of the two. Will take few calculations. I normally have one thats equal to .015 to .02 change in the main that I use. This way when you close it the system is just basically .015 or so rich. Its enough to cool the motor some but not so much as to make it excessive rich. At end of day heat motor up to around 200 or so using shut off to build heat.Shut it down and open vc vent or something to let fumes out. Having vac pump may make this not needed. Using Brad Penn oil. You may have to change a little sooner if your trying to run half of season on one oil fill but is not going to milk oil in one or two weekends.
Jetting example.Normal 130 is equal to 120and 40  or very close.I close of the 40.Normal 130 around 3.78 gpm( figures from chart using 150 psi that I got from Ol Ralph Gorr 25 years ago) and 120 3.41 so Im .3gpm rich. Each system as always is little different depending on pressure and total flow for pump and whats needed for engine. This is just one example we have run using 80A 6.8 gpm pump.

I have run systems like this for years and never had issue. Well except for being told I could not do what I was doing. Like I said system needs to be in good tune.If running too fat it will milk oil.If running too lean it will have hard time over coming combustion chamber heat from the run. Most of the time I don't need it for long period.

 As most who have much of anything I post I don't have problem experimenting and working on car like its pro class car.As matter of fact I love that part.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Fitting Leak
« Reply #7 on: September 29, 2014, 06:34:15 PM »
Sorry should have sent PM did not mean to hi jack thread. Back to the regular programing.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: Fitting Leak
« Reply #8 on: September 30, 2014, 05:21:20 AM »
Sorry should have sent PM did not mean to hi jack thread. Back to the regular programing.

Even if the thread gets diverted a little it is still info that is better out there where everyone can see it rather than filed away in PM's.

Roo
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: Fitting Leak
« Reply #9 on: September 30, 2014, 05:46:54 AM »
Sorry should have sent PM did not mean to hi jack thread. Back to the regular programing.

Even if the thread gets diverted a little it is still info that is better out there where everyone can see it rather than filed away in PM's.

Roo

Yep
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline BK

  • Sr. Member
  • ****
  • Posts: 310
    • View Profile
  • Your Best Time: 8.45 / 5.30
  • Your Track: Empire Dagway
  • Your Vehicle: Late 70's FED
Re: Fitting Leak
« Reply #10 on: September 30, 2014, 09:27:47 AM »
I was thinking the same. Better everyone sees it. Then we know what your up to.

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Fitting Leak
« Reply #11 on: September 30, 2014, 03:45:12 PM »
Sorry BK can'y let everyone know what I am up to they might be asked to testify. Practicing to be politician just got to get thru lying 101,102,103,104,105,106,107,108,109 and 110.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot