Author Topic: Parachute Maintenance  (Read 6427 times)

Offline beargeorge

  • Newbie
  • *
  • Posts: 30
    • View Profile
  • Your Best Time: 7.48 in 1/4
  • Your Track: New England Dragway
  • Your Vehicle: 23T Altered
Parachute Maintenance
« on: September 19, 2014, 10:42:01 AM »
 recently i purchased two used Stroud chutes,they are in good shape but could use a good cleaning, what is the best method to use. thanks, Bob George

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Parachute Maintenance
« Reply #1 on: September 19, 2014, 10:54:28 AM »
 I always washed mine in large bucket with dish washing liquid and water,rinse cpl times and hang out to dry. I know guys who washed them in machine and only problem was upset wife. Not as much as mine when I heat heads in oven to install new guides.LOL
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

dreracecar

  • Guest
Re: Parachute Maintenance
« Reply #2 on: September 19, 2014, 06:21:34 PM »
take the pilot off, gental machine , warm water, spin dry (no heat) then hang.

The most important thing is tying the shroud lines so they dont become tangled. Zip tie close to the chute and every 10" or one can do an electricians knot and zip tie the base

Offline Nightmare AA/FA

  • Full Member
  • ***
  • Posts: 128
    • View Profile
  • Your Track: Bakersfield, CA
  • Your Vehicle: 1934 Ford AA/FA
Re: Parachute Maintenance
« Reply #3 on: September 19, 2014, 08:23:27 PM »
If you don't want to piss off the wife take the chutes to your local Laundromat and use the large machine. 

Offline slingshot383

  • Full Member
  • ***
  • Posts: 143
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: Parachute Maintenance
« Reply #4 on: September 20, 2014, 04:25:41 AM »
And remember, a little baby powder goes a long way on a chute, no need to use the whole can!  (I've seen it done, quite a sight when the chute pops)!
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club

Offline beargeorge

  • Newbie
  • *
  • Posts: 30
    • View Profile
  • Your Best Time: 7.48 in 1/4
  • Your Track: New England Dragway
  • Your Vehicle: 23T Altered
Re: Parachute Maintenance
« Reply #5 on: September 20, 2014, 06:49:17 AM »
Thank you all for your help.  Bob George

Offline LaneM

  • Newbie
  • *
  • Posts: 25
    • View Profile
  • Your Best Time: 8.68 1/4
  • Your Engine: BBC 548ci crowler injected alky
  • Your Track: RMR West Valley,Utah
  • Your Vehicle: front engine digger of course
Re: Parachute Maintenance
« Reply #6 on: October 02, 2014, 10:33:51 PM »
just another thought that I guess most know is that if you aren't running your ride within the next couple days it is best to pop your chute and let it hang so as to keep heavy winkles and such out which helps it deploy faster also this takes the tention out of your spring if that's how you launch..food for thought ;D