Author Topic: flow ? for spud  (Read 5493 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
flow ? for spud
« on: September 17, 2014, 11:05:51 AM »
Spud,

 have question reguarding fuel flow and fitting sizes.  This is more of nitrous thing and know not your speciality. A solenoid that has .312 orfice 1/8 entering and leaving. 1/8 pipe fitting has about .185 bore. In your opion can it flow more than the smallest hole,being .185

 Also while on subject. How much do the electric lean outs you sale flow and do you have richening solenoid also?
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: flow ? for spud
« Reply #1 on: September 17, 2014, 02:11:25 PM »

 The smallest hole will dictate the flow. The radii on the entry, the finish in the hole and the lenth of that smallest hole size will determine a lot about how much it flows.

 Our valves (lean out and enrichment):
 http://fuelinjectionent.com/webstore/product_info.php?products_id=181
 http://fuelinjectionent.com/webstore/product_info.php?products_id=182

 ...all the specs are there. While they can handle 3500 PSI, they are intended to flow liquid and not super cold nitrous gas. They may work just fine for nitrous, but I can't say that because I just don't know.

 Spud

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: flow ? for spud
« Reply #2 on: September 19, 2014, 09:35:38 AM »
not going to use for the nitrous but for fuel side of it. Thanks for verifing what I thought and was debating with someone else. I would send commision , but hard to ship part of case of beer.LOL
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline jeff/21

  • Full Member
  • ***
  • Posts: 186
    • View Profile
  • Your Best Time: 8.24
  • Your Track: any with-in a 6hr radius
  • Your Vehicle: fed
Re: flow ? for spud
« Reply #3 on: September 28, 2014, 06:57:27 PM »
can i ask a question? can the the electric lean-out  be wired to a boost sensor to be activated a a specific value

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: flow ? for spud
« Reply #4 on: September 29, 2014, 06:48:44 AM »

 Sure! It can be wired to any kind of switch...RPM, boost, time, whatever you can imagine.

 Spud

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions