FEDs Forever!
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
Help
Calendar
Login
Register
FrontEngineDragsters.Org Forum
»
Technical
»
Roo Man's Room
(Moderator:
rooman
) »
Which center section?
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Which center section? (Read 7208 times)
JeffV8
Sr. Member
Posts: 259
Your Track: Quaker city
Your Vehicle: 164" Woody Gilmore Flexie
Which center section?
«
on:
September 08, 2014, 08:17:10 PM »
What one should I use in my 1966 Woody dragster? A 741 742 or 846 for that era.
Thanks
Jeff
Logged
Pipe Dreams
Jr. Member
Posts: 79
Your Best Time: 8.09@165
Your Engine: 416 small block MOPAR
Your Track: Milan,Mi or Norwalk,Oh
Your Vehicle: 170" woody gilmore fed
Re: Which center section?
«
Reply #1 on:
September 09, 2014, 04:02:46 AM »
742 would be my first choice. Second would be a 489.
Logged
dreracecar
Guest
Re: Which center section?
«
Reply #2 on:
September 09, 2014, 08:26:11 AM »
742 is better than the 489 although both will work fine and if its just a Cacklecar anyone of the three, although I dont know what spline is on the pinion of the 741 and if a coupler is made for it, if it is different.
The 742 has an 1 3/4"dia pinion shaft vs the 489 1 7/8 which might make you think the 489 is better but the case is the the pinion bearings are larger in the 742 so they take the load better.
What also makes the 742 better is that the pre-load is set with shims and the nut is torqued in place whereas the 489 is a crush sleeve and you tighten the locknut untill preload is met.
Logged
JeffV8
Sr. Member
Posts: 259
Your Track: Quaker city
Your Vehicle: 164" Woody Gilmore Flexie
Re: Which center section?
«
Reply #3 on:
September 09, 2014, 09:33:35 AM »
741 has a 1 3/8 pinion. I found one for $100 I guess I will pass on it.
Thanks for the info
Jeff
Logged
janjon
Full Member
Posts: 208
Your Best Time: 5.74/124 1/8
Your Engine: SB Chev, gas, 350ish
Your Track: Houston Motorsports Park
Your Vehicle: '65-ish 150" SBC/Glide FED
Re: Which center section?
«
Reply #4 on:
September 09, 2014, 07:48:07 PM »
If I wasn't such a smart feller, though some would say I'm just a fart smeller, I would have no idea you were talking 'bout Mopar 8-3/4" rears.
Logged
Just keep the same amount of stuff on the right
as there is on the left. Seeing straight ahead is highly overrated....
JeffV8
Sr. Member
Posts: 259
Your Track: Quaker city
Your Vehicle: 164" Woody Gilmore Flexie
Re: Which center section?
«
Reply #5 on:
September 09, 2014, 08:33:40 PM »
Until you mentioned it I didn't realize I didn't say mopar. But like you anyone in the mopar rear ends know what I was asking lol
Logged
slingshot383
Full Member
Posts: 143
Your Best Time: 1/4 mi. 7.95 @ 168
Your Engine: Chrysler, alcohol, 528 cu.in.
Your Track: Gateway Motorsports Park (the Swamp)
Your Vehicle: Undercover Chassis 23T altered
Re: Which center section?
«
Reply #6 on:
September 10, 2014, 03:52:06 AM »
If you need a new pig, look into the aluminum one that Mopar Performance sell. It's based on the 742 case, and is lighter. Is your 8 3/4 a full floater? The one in my Woody car was, lots of fun finding the bearings and seals.
Logged
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club
George
Hero Member
Posts: 515
Your Vehicle: 1964 Mercury Comet Super Stock/ M automatic
General Location: Midwest USA
Re: Which center section?
«
Reply #7 on:
September 10, 2014, 07:39:08 AM »
I have been putting the iron 742 to the test in our 1700# blown SBC FED. Last time out went 4.61,4.59,4.59 with two .99 60' ( 1/8 mile). Leaving off the trans. brake at 5400 . If there were more season left I would replace the 12 X 33 with some 14". Probably build a Ford 9" for the car this winter.
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
FrontEngineDragsters.Org Forum
»
Technical
»
Roo Man's Room
(Moderator:
rooman
) »
Which center section?