Author Topic: fastest et  (Read 14191 times)

Offline Norm

  • Newbie
  • *
  • Posts: 1
    • View Profile
  • Your Track: Sydney dragway
  • Your Vehicle: fed
fastest et
« on: August 04, 2014, 05:13:48 AM »
HI all
 I'm new to this forum and was hoping someone could help me out with the fastest ET for a SBC front engine dragster on ALCOHOL.
I am running a 406 with an 871 and just ran our first 6 second pass with a 6.92 @ 192mph.

Thanks Norm.

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2010
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: fastest et
« Reply #1 on: August 04, 2014, 06:26:38 AM »
HI all
 I'm new to this forum and was hoping someone could help me out with the fastest ET for a SBC front engine dragster on ALCOHOL.
I am running a 406 with an 871 and just ran our first 6 second pass with a 6.92 @ 192mph.

Thanks Norm.

"N O R M" (from Cheers, you probably have never heard that before.

Nice pass.
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: fastest et
« Reply #2 on: August 04, 2014, 06:28:42 AM »
welcome. Not sure fastest pass with blower I know Scott Parks went 6.77@197 with 383 injected alky. Yea was not a cheap SBC needless to say.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

dreracecar

  • Guest
Re: fastest et
« Reply #3 on: August 04, 2014, 07:49:43 AM »
Switch to a 6-71 and you will be quicker, Too much HP draw with an "8"as you dont need the extra volume. Jason Ritchey ran some 60''s in N-A/F.  Been low 80's with a 377 and a 6-71 without killing it

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: fastest et
« Reply #4 on: August 04, 2014, 11:42:33 AM »
Been 6.94 with mine with a little help from a nitrous bottle ! I would think that Dale Hall would still have been the quickest . The next time I see his son I will ask . Congrat's on your 6 second run ! Bill
« Last Edit: August 04, 2014, 12:35:12 PM by masracingtd1167 »

Offline Paul New

  • Hero Member
  • *****
  • Posts: 743
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: fastest et
« Reply #5 on: August 04, 2014, 01:03:38 PM »
Wasn't Santos quicker than Hall? But I do know that Jack Frost with his blown alky SBC with a screw ran 6 teens he really wanted a 5 second pass out of his altered but never got it, this was all used Santos parts. My SBC has gone 6.66 at 213 in my FED. But yes Parks is FAST with his injected alky SBC!!!!!!!!!!!!!!!!!!

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1110
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: fastest et
« Reply #6 on: August 04, 2014, 02:31:08 PM »
Dale went a 6.52 with his but that was back in 1979!!

Offline coupemerc

  • Sr. Member
  • ****
  • Posts: 306
    • View Profile
  • Your Best Time: 3.86@188 (1/8 Mile), 5.97@233 (1/4 Mile)
Re: fastest et
« Reply #7 on: August 04, 2014, 03:58:30 PM »
I remember seeing Dale run some 6.20s with a Blown Alky SBC in a FED back around 1988-1989 at Maple Grove. Dale had a blower on top of a tunnel ram and the longest blower belt that I had ever seen. The car would slightly shred the blower belt on each pass (he had only one belt) and he would clean up the belt by narrowing it after each run. Dale made it all the way to the finals and came to the line with a belt that was about 1 inch wide. Unfortunately the belt gave up in the final. Everyone in the crowd was loosing their mind watching the little Chevy beat all the Hemi cars. I'd love to hear Scott tell the story.
For unblown...both Scott Parks and Brian Darcy have gone 6.76 in A/ND trim. Engines are in the 380-385 CI range. In$ane!

Offline buickfed

  • Full Member
  • ***
  • Posts: 191
    • View Profile
Re: fastest et
« Reply #8 on: August 04, 2014, 05:59:47 PM »
the dale and norm show was always great to see. and always fun talking to them in the pits or their shop.

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 570
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: fastest et
« Reply #9 on: August 04, 2014, 08:44:13 PM »
Switch to a 6-71 and you will be quicker, Too much HP draw with an "8"as you dont need the extra volume. Jason Ritchey ran some 60''s in N-A/F.  Been low 80's with a 377 and a 6-71 without killing it

Bruce,
For the same air flow, a 6-71 needs to spin faster than a 8-71. So perhaps the HP demand may not be necessarily higher with the 8-71. I'd also think that the charge temperature out of a 6-71 (spinning faster) is hotter than a 8-71 spinning slower, so even with the same boost level, the 8-71 would deliver a denser change.

Does it make sense to you?

Offline cknight

  • Newbie
  • *
  • Posts: 4
    • View Profile
Re: fastest et
« Reply #10 on: August 05, 2014, 02:08:17 PM »
the dale and norm show was always great to see. and always fun talking to them in the pits or their shop.
For those that may have missed it, Norm Case passed away last month. He purchased Precision Automotive from Dale about a decade ago when Dale retired, and has turned out a lot of fine engines.   Regards, Chase

dreracecar

  • Guest
Re: fastest et
« Reply #11 on: August 05, 2014, 04:58:15 PM »
Its about air compression and making the most pressure with the least HP draw. If I could (on my car) run a 4-71 and fill the volume requirments I would because the amount of energy required to spin the rotors would be far less. Santos ran some big numbers years ago after switching to a screw blower, not because it made more pressure, it was because it took 300hp less to run it.  Compressing air inside the manifold is fighting the rotors and trying to spin them backwords. the extra lenght of the "8" is leverge you are fighting if you are not depleting the air volume in the manifold. If your theory was true, why not run a 10,12 or 14-71 and underdrive it---because you want pressure and underdriving it will only take longer to make pressure.
When running Alc as a fuel the intake charge is around 64*. Gas being burned as a vapor, the droplets can heat up very quickly and become detonaton sensitive and thus intercoolers and chillers under the blower densify the charge, Alc burns as a liquid and at 2.1 times the volume as gas does not heat up and there for not likely prone to detonation.

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 570
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: fastest et
« Reply #12 on: August 05, 2014, 05:42:04 PM »
Its about air compression and making the most pressure with the least HP draw. If I could (on my car) run a 4-71 and fill the volume requirments I would because the amount of energy required to spin the rotors would be far less. Santos ran some big numbers years ago after switching to a screw blower, not because it made more pressure, it was because it took 300hp less to run it.  Compressing air inside the manifold is fighting the rotors and trying to spin them backwords. the extra lenght of the "8" is leverge you are fighting if you are not depleting the air volume in the manifold. If your theory was true, why not run a 10,12 or 14-71 and underdrive it---because you want pressure and underdriving it will only take longer to make pressure.
When running Alc as a fuel the intake charge is around 64*. Gas being burned as a vapor, the droplets can heat up very quickly and become detonaton sensitive and thus intercoolers and chillers under the blower densify the charge, Alc burns as a liquid and at 2.1 times the volume as gas does not heat up and there for not likely prone to detonation.

That's the voice of experience, I hear you Bruce, thanks!

Offline slingshot383

  • Full Member
  • ***
  • Posts: 143
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: fastest et
« Reply #13 on: August 06, 2014, 03:37:53 AM »
www.draglist.com is the place you want to look, and put your info in so that you are on the list.
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: fastest et
« Reply #14 on: August 06, 2014, 01:55:03 PM »
yea but be warned you can be moved down that list pretty quick.My last alky dragster pass is around 225  or so.But hey it was 16 years ago. Nothing money can't fix. Dang I love the ride in blower car.Real blower not that under drive stuff.Sorry Glenn couldn't resist,didn't try too hard though.LOL
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot