« previous next »
Pages: [1]   Go Down

Author Topic: Stud pull  (Read 5477 times)

Offline MaggiFinn

  • Jr. Member
  • **
  • Posts: 54
    • View Profile
  • Your Engine: SBC 355-406
  • Your Track: Kvartmiluklubburinn
  • Your Vehicle: FED
Stud pull
« on: July 09, 2014, 11:46:41 AM »
 As we just finished fixing the deck on the 400sbc again, I wanted to share with you guys a link I found, regarding the effects of fine threads on stud pull when coarse thread torque values are used.

http://www.futek.com/boltcalc.aspx

When used in aftermarket engine blocks, the added clamping force from fine thread studs and nuts may be fine, but when using 40+years old iron the chance of pulling out threads and cracking components increase dramaticly.
Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: Stud pull
« Reply #1 on: July 09, 2014, 02:45:32 PM »
Interesting info but remember--on a 400 SBC it is 50/50 chance being cracked  on the deck between bore and head bolt hole that is nearest the cylinder--hard to find one that is not --I see dozens throughout the year and many are cracked after clean up and inspection--it is a 400 Thang!
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 570
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: Stud pull
« Reply #2 on: July 09, 2014, 03:45:19 PM »
Quote from: dusterdave173 on July 09, 2014, 02:45:32 PM
Interesting info but remember--on a 400 SBC it is 50/50 chance being cracked  on the deck between bore and head bolt hole that is nearest the cylinder--hard to find one that is not --I see dozens throughout the year and many are cracked after clean up and inspection--it is a 400 Thang!

I agree! The decks of my SBC 400 block (Chevy PN 776509) have probably half a dozen of cracks. There are cracks between threads and coolant passages, between threads and steam holes. On thread has two cracks 180 degreees apart, one to a coolant passage and the the other to a steam hole. This block is on borrowed time, but it's still going strong!

It's tall filled with HardBlok, the coolant galleries are about one inch deep.
Logged

Offline alkyal

  • Jr. Member
  • **
  • Posts: 52
    • View Profile
  • Your Track: Quaker City/Dragway 42
  • Your Vehicle: Not a Driver-Nostaliga AA/FD
Re: Stud pull
« Reply #3 on: July 13, 2014, 09:49:06 AM »
When preping a 400 CI block, I use Iron-tite crack repair plugs to plug the Steam Holes [after tapping hole with tapered tap]. Install with 609 Locktite-TIGHT. Cut off above deck and finish off when decking block. This seems to help control the potential for future cracks and limit those that have started. I will only use studs in these old blocks. Some blocks are so BAD that pulling out the threads cant be avoided. I check and repair all before doing any machine work.  [Just remember to set repair insert below deck,so as not to hit it when decking] Its too bad many good 400 blocks went to the junkyard yrs ago. If needed I have a Std. bore 400 block that has been cleaned and pressure tested. Also has a set of 4 bolt steel caps/studs with it/but NOT installed. I am in North Central Ohio.
Logged
Pages: [1]   Go Up
« previous next »